Location:
Search - 12864-3 L
Search list
Description: 12864液晶显示程序 12864液晶显示程序-12,864 procedures LCD liquid crystal display LCD procedures 12864 128 procedures 64 LCD process 12,864 LCD procedures
Platform: |
Size: 3072 |
Author: |
Hits:
Description: //DM430-L型最小系统板控制带字库型12864液晶模块显示测试程序
//显示模式为汉字模式,直接将12864插入12864接口即可
//注意选择液晶的电源,位于电位器附近,可选5V或3.3V,根据液晶电压进行选择
//调试环境:EW430 V5.30-
//DM430-L, the minimum system board control with font-12864 LCD module display test program
//Display mode for character mode, directly to the 12864 insert 12864 interface to
//Note to select the LCD power supply, located near the potentiometer, optional 5V or 3.3V, according to the LCD voltage selection
//Debugging environment: EW430 V5.30
Platform: |
Size: 21504 |
Author: wujunkai |
Hits:
Description: 1.VR1 为 3X3 体积硬封 10K 可调电位器,可以进行对比度调节。当电位器缺口
大致对准 R1 电阻时,此时液晶屏对比度为正常范围内,显示较清晰,可以液晶
接口第三脚 V0 不用接。
当电位器缺口对准 VR1 丝印时,此时相当于电位器是零电阻值,可以用螺丝刀
手动调节液晶电位器至 R1 位置直到显示屏正常清晰显示
液晶屏自己带电位器时,第三脚 V0 可接可不接,不接必须调节液晶背面电位器
至 R1 位置。接了 V0 可以通过外接电位器调节,同时也可以用液晶电位器调。
2.液晶接口 18 脚 VOUT 可以不接 悬空
3.串并行显示可通过下列两种方式调节:
一种 PSB 脚控制 程序内部高低电平选择 H-并行;L-串行
二种 JP2 短路点有 3 点,S 和中间点连起来为串行 P 点和中间点连起来为并行
如取字模出现乱码时,请一定把 JP2 短接 P 为并口 S 为串口
4:此液晶屏只支持一种电压,发货为 5V 只支持 5V ,3.3V 只支持 3.3V-1.VR1 hard seal 10K for 3X3 volume adjustable potentiometer, the contrast can be adjusted. When the potentiometer gap
When roughly aligned R1 resistance, and the LCD display contrast within the normal range, showing more clearly, can the LCD
The third leg V0 interface not connected.
When VR1 potentiometer alignment notch silk, then the equivalent potentiometer resistance value is zero, you can use a screwdriver
Potentiometer to manually adjust the LCD display normal R1 position until a clear display
When the LCD screen yourself potentiometer, the third leg V0 can be accessed from time to connect, then do not have to adjust the LCD back potentiometer
To R1 position. V0 can pick up an external potentiometer adjustment, but you can also use the LCD potentiometer adjustment.
2. LCD Interface 18-pin VOUT can not take vacant
3 serial parallel display can be adjusted by the following two ways:
One kind of PSB feet high and low level of internal control procedures to select H
Platform: |
Size: 961536 |
Author: 方跃东 |
Hits: