Location:
Search - FS44B0X
Search list
Description: 1）通过fs44b0xbios和网口，将upload里的boot.bin烧写到flash 0 地址
见“FS44B0Xbios使用指南”之5
2) 打开57600超级终端
3) 连上串口线和jtag调试头
4）打开FS44B0X开发板电源
5）运行jtag.exe,在SDT下调入 ucosii_demo.axf，运行
6) 在超级终端上有三个任务的运行与退出显示，板子上的三个发光二极管会来回闪烁。
-a) fs44b0xbios and LAN, li will upload the burning of flash boot.bin 0 addresses see "FS44B0Xbio s User's Guide "5 2) to open 57,600 Super Terminal 3) connected to serial lines and the first four JTAG Debugging) Open FS44B0X development board Power 5) Run jtag.exe, under the redeployment ucosii_demo.axf SDT, running 6) of the Super Terminal 3 on the mandate of the operation and withdraw from the show, on board the three light-emitting diodes will flicker back and forth.
Platform: |
Size: 215299 |
Author: 张淼林 |
Hits:
Description: lcddemo-1（2004版） -- 320X240 STN 灰度LCD 测试
此代码在SDT2.51下调试通过。运行时LED会闪烁一下，接着串口0会输出一些系统信息,在波特率为57600超级终端可看到,打印出来的由ASCII字符组成的 FS44B0X图样，此时LCD上显示ascii字符组成的ARM图样。通过串口终端与系统交互，可以测试320X240 STN LCD,包括图形显示函数，ascii字符显示函数。
-lcddemo-1 (2004 version) -- 320x240 STN LCD Gray this test under the code debugging SDT2.51 through. Runtime LED flashes that went 0 serial number system will output information, the baud rate of 57,600 super terminal can be seen, Print out by the characters of ASCII FS44B0X drawings, this LCD display ascii characters of the ARM design. Through serial terminal and system interaction, can test 320x240 STN LCD, including graphics function, ascii character display function.
Platform: |
Size: 139291 |
Author: 张淼林 |
Hits:
Description: 1. beep -- PWM测试
为 ADS1.2 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后在57600的超级终端里按PC机键盘的“+”“-” 按键，可以听到BUZZ增大减小的声音。
2. key -- 按键测试
为 SDT2.51 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后按FS44B0X上的按键key1 key2 key3 key4 相应的发光二极管亮
3 keyint -- 按键中断测试
该项目在SDT2.51下编译调试。主程序是while空循环，中断服务程序对应四个按键做相应的处理，key1 按键点亮D1灯，并在串口打印信息，因为没有加按键去抖动程序，所以，一次按键，产生几次中断。
-1. Beep -- PWM ADS1.2 testing for the project under the Build, in the ADW sdt2.51 Lane debugging, after running the 57,600 in the Super Terminal Lane by PC keyboard "" "-" buttons, Buzz can be increased to reduce heard voices. 2. Key -- SDT2.51 key test for the project under the Build, in the ADW sdt2.51 Lane debugging, after running the program on the button FS44B0X key1 key2 key3 key4 corresponding LED top-three keyint -- interrupted test button in the project under the Build SDT2.51 debugging. While space is the main program cycle, interrupt service routine correspondence four keys handled accordingly. key1 D1 lights lit keys, and Serial Print information, because no buttons to increase jitter, and therefore, a button. several have interrupted.
Platform: |
Size: 507339 |
Author: 张淼林 |
Hits:
Description: 优龙FS44B0X开发板原理图及PCB，虽然都是PDF格式，但是可以作为参考资料。-Long FS44B0X development board diagram and the PCB, although are in PDF format, However, it as a reference.
Platform: |
Size: 800766 |
Author: 任亮 |
Hits:
Description: uClinux EEROM驱动，基于S3C44B0X-uClinux EEROM-driven, based on S3C44B0X
Platform: |
Size: 6712 |
Author: 刘丙毓 |
Hits:
Description: arm7开发板fs44b0x原代码
说明：
1) 本项目在ADS1.2下编译,在SDT2.51的ADW中调试。编译时，请将整个fs44b0xbios目录拷贝到c:\\下
2) 现在只对39VF160烧入,对其他FLASH可自改,注意要修改BIOS的驻留地址,现地址为0X1F0000.
3) 对不同的RAM而言,修改SYSINIT.S里的参数.FS44B0Xbios运行地址为0XC7C0000,可在ADS中修改.
4) 波特率为57600
5) ip地址为 192.168.0.1-arm7 Development Board fs44b0x original code : 1) the item under the ADS1.2 compiler, which originated SDT2.51 of debugging. Compiling, I would be grateful if the entire fs44b0xbios copy of the directory c : \\ under 2) now only 39 VF160 burned right into the other FLASH, will be changed, attention to the presence of BIOS changes addresses, is located at 0 X1F0000. 3) the different RAM, Lane changes SYSINIT.S parameters. FS44B0Xbios running at 0 XC7C000 0, ADS can be modified. 4) baud rate of 57600 5) ip address 192.168.0.1
Platform: |
Size: 459006 |
Author: zhouchendong |
Hits:
Description: FS44B0X板的IIC程序测试-------源代码-FS44B0X plate IIC test procedures ------- source code
Platform: |
Size: 17092 |
Author: 山山 |
Hits:
Description: uCOS II的FS44B0X II移植版本，直接编译就可以在板子上跑了-uCOS II FS44B0X transplant II version can be directly translated in a run on the board
Platform: |
Size: 564239 |
Author: 李翔 |
Hits:
Description: bootload说明
fs44b0x开发板的bootload详细说明
Platform: |
Size: 295495 |
Author: 悍天雷 |
Hits:
Description: S3C44B0X开发板上USB应用代码，PC机部分的软件1) LEDDEMO -- 控制 SW44B0板上三个LED的程序2) D12_DRIVER_FOR_WIN98 -- USB芯片WIN98的驱动程序FS44B0X板的USB固件程序--源代码USB_DEMO-S3C44B0X development board USB application code, part of the PC software 1) LEDDEMO -- SW44B0 control board three LED procedures 2) D12_DRIVER_FOR_WIN98 -- USB chip Win98 driver FS44B0X board USB Firmware -- source code USB_ DEMO
Platform: |
Size: 272296 |
Author: 李爱成 |
Hits:
Description: uCOS II的FS44B0X II移植版本，直接编译就可以在板子上跑了-uCOS II FS44B0X transplant II version can be directly translated in a run on the board
Platform: |
Size: 564224 |
Author: 李翔 |
Hits:
Description: S3C44B0X开发板上USB应用代码，PC机部分的软件1) LEDDEMO -- 控制 SW44B0板上三个LED的程序2) D12_DRIVER_FOR_WIN98 -- USB芯片WIN98的驱动程序FS44B0X板的USB固件程序--源代码USB_DEMO-S3C44B0X development board USB application code, part of the PC software 1) LEDDEMO-- SW44B0 control board three LED procedures 2) D12_DRIVER_FOR_WIN98-- USB chip Win98 driver FS44B0X board USB Firmware-- source code USB_ DEMO
Platform: |
Size: 272384 |
Author: 李爱成 |
Hits:
Description: fs44b0x_usb -- usb 测试程序
PC机部分的软件
1) LEDDEMO -- 控制 FS44B0X板上三个LED的程序
2) D12_DRIVER_FOR_WIN98 -- USB芯片WIN98的驱动程序
3) D12_DRIVER_FOR_WINXP -- USB芯片WINXP的驱动程序
FS44B0X板的USB固件程序--源代码
USB_DEMO
使用方法：
1）在SDT2.51里调入usb_demo.axf, 运行。
2）接上usb电缆，安装win98的d12驱动程序（或者winxp的d12驱动程序）
3) 运行 LEDDEMO ，用鼠标点击led1, led2, led3,可以看到FS44B0X板上三个LED亮灭。
-fs44b0x_usb-- usb test procedure part of the PC software 1) LEDDEM O-- FS44B0X control board three LED procedures 2) D12_DRIVER_FOR_W IN98-- USB chip Win98 driver 3) D12_DRIVER_FOR_WI NXP-- USB chip WINXP driver FS44B0X board USB firmware-- the source of generation code USB_DEMO Use : 1) In SDT2.51 Lane transferred usb_demo.axf running. 2) connected to the USB cable, win98 installation of the D12 driver (or the D12 winxp drivers) 3) Operation LEDD EMO with mouse clicks led1, led2, led3. FS44B0X can see three LED board-eliminate.
Platform: |
Size: 219136 |
Author: 张淼林 |
Hits:
Description: 1）通过fs44b0xbios和网口，将upload里的boot.bin烧写到flash 0 地址
见“FS44B0Xbios使用指南”之5
2) 打开57600超级终端
3) 连上串口线和jtag调试头
4）打开FS44B0X开发板电源
5）运行jtag.exe,在SDT下调入 ucosii_demo.axf，运行
6) 在超级终端上有三个任务的运行与退出显示，板子上的三个发光二极管会来回闪烁。
-a) fs44b0xbios and LAN, li will upload the burning of flash boot.bin 0 addresses see "FS44B0Xbio s User's Guide "5 2) to open 57,600 Super Terminal 3) connected to serial lines and the first four JTAG Debugging) Open FS44B0X development board Power 5) Run jtag.exe, under the redeployment ucosii_demo.axf SDT, running 6) of the Super Terminal 3 on the mandate of the operation and withdraw from the show, on board the three light-emitting diodes will flicker back and forth.
Platform: |
Size: 215040 |
Author: 张淼林 |
Hits:
Description: lcddemo-1（2004版） -- 320X240 STN 灰度LCD 测试
此代码在SDT2.51下调试通过。运行时LED会闪烁一下，接着串口0会输出一些系统信息,在波特率为57600超级终端可看到,打印出来的由ASCII字符组成的 FS44B0X图样，此时LCD上显示ascii字符组成的ARM图样。通过串口终端与系统交互，可以测试320X240 STN LCD,包括图形显示函数，ascii字符显示函数。
-lcddemo-1 (2004 version)-- 320x240 STN LCD Gray this test under the code debugging SDT2.51 through. Runtime LED flashes that went 0 serial number system will output information, the baud rate of 57,600 super terminal can be seen, Print out by the characters of ASCII FS44B0X drawings, this LCD display ascii characters of the ARM design. Through serial terminal and system interaction, can test 320x240 STN LCD, including graphics function, ascii character display function.
Platform: |
Size: 139264 |
Author: 张淼林 |
Hits:
Description: 1. beep -- PWM测试
为 ADS1.2 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后在57600的超级终端里按PC机键盘的“+”“-” 按键，可以听到BUZZ增大减小的声音。
2. key -- 按键测试
为 SDT2.51 下编译的项目, 在sdt2.51的ADW里调试，该程序运行后按FS44B0X上的按键key1 key2 key3 key4 相应的发光二极管亮
3 keyint -- 按键中断测试
该项目在SDT2.51下编译调试。主程序是while空循环，中断服务程序对应四个按键做相应的处理，key1 按键点亮D1灯，并在串口打印信息，因为没有加按键去抖动程序，所以，一次按键，产生几次中断。
-1. Beep-- PWM ADS1.2 testing for the project under the Build, in the ADW sdt2.51 Lane debugging, after running the 57,600 in the Super Terminal Lane by PC keyboard "" "-" buttons, Buzz can be increased to reduce heard voices. 2. Key-- SDT2.51 key test for the project under the Build, in the ADW sdt2.51 Lane debugging, after running the program on the button FS44B0X key1 key2 key3 key4 corresponding LED top-three keyint-- interrupted test button in the project under the Build SDT2.51 debugging. While space is the main program cycle, interrupt service routine correspondence four keys handled accordingly. key1 D1 lights lit keys, and Serial Print information, because no buttons to increase jitter, and therefore, a button. several have interrupted.
Platform: |
Size: 506880 |
Author: 张淼林 |
Hits:
Description: 优龙FS44B0X开发板原理图及PCB，虽然都是PDF格式，但是可以作为参考资料。-Long FS44B0X development board diagram and the PCB, although are in PDF format, However, it as a reference.
Platform: |
Size: 800768 |
Author: 任亮 |
Hits:
Description: uClinux EEROM驱动，基于S3C44B0X-uClinux EEROM-driven, based on S3C44B0X
Platform: |
Size: 6144 |
Author: 流域 |
Hits:
Description: arm7开发板fs44b0x原代码
说明：
1) 本项目在ADS1.2下编译,在SDT2.51的ADW中调试。编译时，请将整个fs44b0xbios目录拷贝到c:\下
2) 现在只对39VF160烧入,对其他FLASH可自改,注意要修改BIOS的驻留地址,现地址为0X1F0000.
3) 对不同的RAM而言,修改SYSINIT.S里的参数.FS44B0Xbios运行地址为0XC7C0000,可在ADS中修改.
4) 波特率为57600
5) ip地址为 192.168.0.1-arm7 Development Board fs44b0x original code : 1) the item under the ADS1.2 compiler, which originated SDT2.51 of debugging. Compiling, I would be grateful if the entire fs44b0xbios copy of the directory c : \ under 2) now only 39 VF160 burned right into the other FLASH, will be changed, attention to the presence of BIOS changes addresses, is located at 0 X1F0000. 3) the different RAM, Lane changes SYSINIT.S parameters. FS44B0Xbios running at 0 XC7C000 0, ADS can be modified. 4) baud rate of 57600 5) ip address 192.168.0.1
Platform: |
Size: 458752 |
Author: zhouchendong |
Hits:
Description: bootload说明
fs44b0x开发板的bootload详细说明
-Bootload fs44b0x development board that a detailed description of Bootload
Platform: |
Size: 294912 |
Author: |
Hits: