Description: 数字系统课程设计包括EDA实验板组装调试及红外遥控系统设计制作两个部分，各部分要求如下：
红外遥控系统由发射编码和接收解码两个部分组成，本课程设计要求制作发射编码电路板（遥控器）以及编写程序在EDA实验板上实现接收解码，具体说明如下：
-Digital System Design courses including EDA experimental plate assembly and testing infrared remote control system design of two parts. Some of the requirements are as follows : infrared remote control system launched by the encoding and decoding receive two components, This course design produced fired coding circuit board (remote control) and the preparation of experimental procedures in EDA board receiver Solutions codes, which are described below : Platform: |
Size: 370360 |
Author: 梁良 |
Hits:
Description: 数字系统课程设计包括EDA实验板组装调试及红外遥控系统设计制作两个部分，各部分要求如下：
红外遥控系统由发射编码和接收解码两个部分组成，本课程设计要求制作发射编码电路板（遥控器）以及编写程序在EDA实验板上实现接收解码，具体说明如下：
-Digital System Design courses including EDA experimental plate assembly and testing infrared remote control system design of two parts. Some of the requirements are as follows : infrared remote control system launched by the encoding and decoding receive two components, This course design produced fired coding circuit board (remote control) and the preparation of experimental procedures in EDA board receiver Solutions codes, which are described below : Platform: |
Size: 369664 |
Author: 梁良 |
Hits:
Description: NEC标准的红外编码程序，用单片机和一红外发射二极管能实现遥控板的功能，对应的还有红外解码程序，稍后找找上传-NEC infrared coding standard procedures, using infrared emitting diode chip and a remote control board to achieve the function, along with the corresponding infrared decoding process, look for later upload Platform: |
Size: 45056 |
Author:张四庆 |
Hits:
Description: 单片机红外遥控解码。红外遥控发射芯片采用PPM编码方式,当发射器按键按下后,将发射一组108ms的编码脉冲。遥控编码脉冲由前导码、8位用户码、8位用户码的反码、8位操作码以及8位操作码的反码组成。
-SCM infrared remote control decoding. Infrared remote control launch chip adopt PPM coding way, when transmitters keys pressed, will launch a group of 108 ms coding pulse. Remote control pulse coding by leading code, eight users code, eight users yards of FanMa, eight operation codes and eight operation codes of the FanMa. Platform: |
Size: 6144 |
Author:zhangdong |
Hits:
Description: 红外遥控器+红外一体化接收头部分的仿真
红外线编码是数据传输和家用电器遥控常用的一种通讯方法，其实质是一种脉宽调制的串行通讯。家电遥控
中常用的红外线编码电路有μPD6121G型HT622型和7461型等。
这里就以这些电路的编码格式来仿真怎样使用单片机的捕获中断功能来实现其解码。 红外线通讯的发送部
分主要是把待发送的数据转换成一定格式的脉冲，然后驱动红外发光管向外发送数据。接收部分则是完成红外
线的接收、放大、解调，还原成同步发射格式相同(但高、低电位刚好相反的脉冲信号)。这些工作通常由一体
化的接收头来完成，主要输出TTL兼容电平。最后通过解码把脉冲信号转换成数据，从而实现数据的传输。
本单元就是来完成一体化接收头接受到的红外遥控器编码后的输出数据,所以只要单片机完成本单元的解码任
务,并成功实现之后,只要将IR引脚接上红外接收头之后就可以实现红外遥控的功能了。
-Infrared coding is data transmission and household appliances remote control a common communication method, its essence is a pulse width modulation of serial communication. Home appliance remote control
The commonly used infrared coding circuit have μ PD6121G type HT622 type and 7461 type, etc.
Here to the circuit code format to simulate how to use a single chip microcomputer capture interrupt function to realize its decoding. Infrared communication sends department
The main points to send data is converted into certain format pulse, and then drive infrared light tube sent out the data. Receiving part is complete infrared
Line of receiving, amplification, demodulation, reductive into synchronous launch the same format (but high and low potential is just the opposite of the pulse signal). These work usually consists of an organic whole
The head of receiving to complete, the main output TTL compatible level. Finally through the decoding the pulse signal conversion to Platform: |
Size: 117760 |
Author:虚无一 |
Hits:
Description: 红外线遥控器源代码,了解红外遥器编码和解码程序，便于开发学习红外遥控技术。-Infrared remote control source code, learn infrared remote device coding and decoding procedures, to facilitate the development of learning infrared remote control technology. Platform: |
Size: 19456 |
Author:马龙 |
Hits:
Description: 该工程详细分析了红外遥控器的编码规则，和应用在STM32下的解码程序，该程序实现按下红外遥控的第一个键，点亮小灯。-The project is a detailed analysis of the infrared remote control coding rules, and applied under the STM32 decoding process, the program implements the first key press infrared remote control, lighting a small lamp. Platform: |
Size: 5853184 |
Author:汪潇文 |
Hits:
Description: NEC协议的红外遥控器编码解码程序，大家收集到的通常是采用定时器中断的方式，我这个代码是采用软件延时的方法实现的，能省掉单片机的一个定时器中断源，一直运用于项目上。(NEC protocol's infrared remote control coding and decoding program. We usually use the way of timer interruption. My code is implemented by software delay. It can save a timer interrupt source of MCU and has been used in projects.) Platform: |
Size: 11264 |
Author:源码师 |
Hits:
Search - Infrared Remote Control coding and decoding