Location:
Search - PB3
Search list
Description: at91sam7s应用
代码说明：
1)完成基本的初始化
2)初始化PIO等
3)驱动板上的四个按键(PB1,PB2,PB3,PB4)
4)初始化DEBUG口，Usart1等
5)初始化定时器timer0,timer1等-at91sam7s application code : 1) completion of the basic initialization 2) initialization three PIO) driver board the four buttons (PB1, PB2. PB3, PB4) 4) initialization DEBUG mouth, Usart1 five) initialize the timer timer0, timer1 etc.
Platform: |
Size: 732827 |
Author: aki |
Hits:
Description: at91sam7s63,ads1.2编译器
本程序为为一个简单的跑马灯演示：
1，完成基本的初始化
2，驱动板上的四个发光二极管(DS1,DS2,DS3,DS4)
3，驱动板上的四个按键(PB1,PB2,PB3,PB4)
4，现象为四个发光二极管不停的依次闪亮
当有PB1按下,闪亮的速度加快
当有PB3按下,闪亮的速度减慢
-at91sam7s63. ads1.2 compiler for the procedure for a simple demonstration of 5,250 : a complete two basic initialization, the four-panel light-emitting diode (DS1 and DS2, DS3, LST), 3 the four-panel buttons (PB1, PB2, PB3, PB4) 4. phenomenon of four LEDs flashing constantly followed the PB1 When pressed, shiny speed when PB3? shiny slower pace
Platform: |
Size: 636715 |
Author: aki |
Hits:
Description: 本程序为完成各种中断的演示.at91sam7s64芯片,ads1.2编译器.代码说明：
1)完成基本的初始化
2)初始化PIO,IRQ,FIQ,software_interrupt等
3)驱动板上的四个按键(PB1,PB2,PB3,PB4)
4)初始化DEBUG口，Usart1等
5)初始化定时器timer0,timer1等-procedures for the completion of the various demonstration interrupted. At91sam7s64 chips ads1.2 compiler. source : 1) completion of the basic initialization 2) initialization PIO, IRQ, FIQ, software_interrupt three) driver board the four buttons (PB1. PB2, PB3, PB4) 4) initialization DEBUG mouth, Usart1 five) initialize the timer timer0, timer1 etc.
Platform: |
Size: 750072 |
Author: aki |
Hits:
Description: m16+cp2200组成的网络接口。
m16使用内部RC振荡8M，如果要提高主频，请注意修改模拟总线读函数。
cp2200模块使用www.icdev.com.cn的，更改pin44连接VCC，即总线复用方式，地址数据复用。
软件编写使用avrstudio4.12+sp4+winavr（avrstudio自带的winavr嵌入方式）。
硬件连接：
m16 | cp2200
PORTA | AD0－7
PB0 | RST
PB1 | CS
PB2 | RD
PB3 | WR
PD2 | INT
PD3 | ALE(A3)
由于采用的是m16做为主控，只能使用总线模拟方式，其读写速度有限，经测试约为双向11.8kBps(90kbps)。
由于ram有限，仅仅采用了332Bytes的数据缓冲做为收发buffer，超过此长度的以太网包将抛弃。
此工程文件仅仅做为cp220x的一个移植范例，高级tcpip应用代码因商业缘故不会提供，请勿找我询问。-m16 cp2200 a network interface. M16 use of internal RC oscillator 8 M, if we are to raise the frequency, please note time change Bus simulation function. Cp2200 module uses www.icdev.com.cn. changes pin44 connecting VCC, bus multiplexing, address data multiplexing. Software programmers use avrstudio4.12 sp4 winavr (bringing their avrstudio winavr embedded in the way). Hardware connections : m16 | cp2200 PORTA | AD0-7 pins | RST PB1 | CS PB2 | RD PB3 | WR NC | INT PD3 | ALE (A3) is used as the main control m16, It can only use bus simulation, the literacy rate is limited, After about a two-way test 11.8 kBps (90kbps). As the ram limited, merely using the 332 Bytes of data as a buffer TX buffer, Over this length of the Ethernet packets will be discarded. This works only as a document of a tr
Platform: |
Size: 101751 |
Author: 刘晓军 |
Hits:
Description: LINUX+9200基础实验 :点亮板子上的LED
驱动程序部分led_module.c
说明:程序默认PBO,PB1,PB2,PB3接LED灯,主设备号43,可根据实际情况修改参数.
Platform: |
Size: 5831 |
Author: 汪龙峰 |
Hits:
Description: 胸外科信息管理系统.rar(powerbuilder)
Platform: |
Size: 2616482 |
Author: 大江 |
Hits:
Description: LCD1602液晶屏的四线驱动模块，可以替换原来的文件，直接使用，函数入口相同。
1、可直接嵌入到项目中使用
2、晶振频率：1M
3、如晶振提高低层驱动延时要作相应修改
4、程序在原来基础上只使用了PB口的高四位，即PB4—PB7，PB0—PB3可以做它用
Platform: |
Size: 41436 |
Author: hu |
Hits:
Description: at91sam7s应用
代码说明：
1)完成基本的初始化
2)初始化PIO等
3)驱动板上的四个按键(PB1,PB2,PB3,PB4)
4)初始化DEBUG口，Usart1等
5)初始化定时器timer0,timer1等-at91sam7s application code : 1) completion of the basic initialization 2) initialization three PIO) driver board the four buttons (PB1, PB2. PB3, PB4) 4) initialization DEBUG mouth, Usart1 five) initialize the timer timer0, timer1 etc.
Platform: |
Size: 732160 |
Author: aki |
Hits:
Description: at91sam7s63,ads1.2编译器
本程序为为一个简单的跑马灯演示：
1，完成基本的初始化
2，驱动板上的四个发光二极管(DS1,DS2,DS3,DS4)
3，驱动板上的四个按键(PB1,PB2,PB3,PB4)
4，现象为四个发光二极管不停的依次闪亮
当有PB1按下,闪亮的速度加快
当有PB3按下,闪亮的速度减慢
-at91sam7s63. ads1.2 compiler for the procedure for a simple demonstration of 5,250 : a complete two basic initialization, the four-panel light-emitting diode (DS1 and DS2, DS3, LST), 3 the four-panel buttons (PB1, PB2, PB3, PB4) 4. phenomenon of four LEDs flashing constantly followed the PB1 When pressed, shiny speed when PB3? shiny slower pace
Platform: |
Size: 636928 |
Author: aki |
Hits:
Description: 本程序为完成各种中断的演示.at91sam7s64芯片,ads1.2编译器.代码说明：
1)完成基本的初始化
2)初始化PIO,IRQ,FIQ,software_interrupt等
3)驱动板上的四个按键(PB1,PB2,PB3,PB4)
4)初始化DEBUG口，Usart1等
5)初始化定时器timer0,timer1等-procedures for the completion of the various demonstration interrupted. At91sam7s64 chips ads1.2 compiler. source : 1) completion of the basic initialization 2) initialization PIO, IRQ, FIQ, software_interrupt three) driver board the four buttons (PB1. PB2, PB3, PB4) 4) initialization DEBUG mouth, Usart1 five) initialize the timer timer0, timer1 etc.
Platform: |
Size: 749568 |
Author: aki |
Hits:
Description: m16+cp2200组成的网络接口。
m16使用内部RC振荡8M，如果要提高主频，请注意修改模拟总线读函数。
cp2200模块使用www.icdev.com.cn的，更改pin44连接VCC，即总线复用方式，地址数据复用。
软件编写使用avrstudio4.12+sp4+winavr（avrstudio自带的winavr嵌入方式）。
硬件连接：
m16 | cp2200
PORTA | AD0－7
PB0 | RST
PB1 | CS
PB2 | RD
PB3 | WR
PD2 | INT
PD3 | ALE(A3)
由于采用的是m16做为主控，只能使用总线模拟方式，其读写速度有限，经测试约为双向11.8kBps(90kbps)。
由于ram有限，仅仅采用了332Bytes的数据缓冲做为收发buffer，超过此长度的以太网包将抛弃。
此工程文件仅仅做为cp220x的一个移植范例，高级tcpip应用代码因商业缘故不会提供，请勿找我询问。-m16 cp2200 a network interface. M16 use of internal RC oscillator 8 M, if we are to raise the frequency, please note time change Bus simulation function. Cp2200 module uses www.icdev.com.cn. changes pin44 connecting VCC, bus multiplexing, address data multiplexing. Software programmers use avrstudio4.12 sp4 winavr (bringing their avrstudio winavr embedded in the way). Hardware connections : m16 | cp2200 PORTA | AD0-7 pins | RST PB1 | CS PB2 | RD PB3 | WR NC | INT PD3 | ALE (A3) is used as the main control m16, It can only use bus simulation, the literacy rate is limited, After about a two-way test 11.8 kBps (90kbps). As the ram limited, merely using the 332 Bytes of data as a buffer TX buffer, Over this length of the Ethernet packets will be discarded. This works only as a document of a tr
Platform: |
Size: 101376 |
Author: 刘晓军 |
Hits:
Description: LINUX+9200基础实验 :点亮板子上的LED
驱动程序部分led_module.c
说明:程序默认PBO,PB1,PB2,PB3接LED灯,主设备号43,可根据实际情况修改参数.-LINUX+ 9200 based on Experiment: LED light board on the driver part led_module.c Description: default PBO, PB1, PB2, PB3 then LED lights, major device number 43, can modify the parameters according to the actual situation.
Platform: |
Size: 5120 |
Author: 汪龙峰 |
Hits:
Description: 胸外科信息管理系统.rar(powerbuilder)-Thoracic surgery information management system. Rar (powerbuilder)
Platform: |
Size: 2616320 |
Author: 大江 |
Hits:
Description: LCD1602液晶屏的四线驱动模块，可以替换原来的文件，直接使用，函数入口相同。
1、可直接嵌入到项目中使用
2、晶振频率：1M
3、如晶振提高低层驱动延时要作相应修改
4、程序在原来基础上只使用了PB口的高四位，即PB4—PB7，PB0—PB3可以做它用-LCD1602 LCD four-lane drive module, you can replace the original documents, direct access, the entrance of the same function. 1, can be directly embedded into the project to use 2, crystal oscillator frequency: 1M 3, such as crystal enhance low-level driver to make consequential amendments to Delay 4, the procedure in the original basis of the PB I use only high-four, that is, PB4- PB7, PB0-PB3 can make it
Platform: |
Size: 40960 |
Author: hu |
Hits:
Description: 用PB3/OC0输出快速PWM波控制直流电机，PC0-3接按键，
按键调节直流电机速度
-With PB3/OC0 fast PWM wave output DC motor control, PC0-3 access keys, buttons adjust the speed of DC motor
Platform: |
Size: 1024 |
Author: 高龙 |
Hits:
Description: This a source of 13.560MHz RFID card reader for TRH031M as ATMEGA8-16AU MPU.
The title is 3Alogics TRH031M 13.56MHz RFID Reader V1.0.
project : RFID Reader V2.0
Target : MEGA8-16AU
Crystal: 16.000 Mhz
Input : TRH031M RFID 13.56MHz
Output : RS232C 115200,N,8,1
Compiler : ICC-AVR V6.26C
// Pin configuration for ATMEGA8-16AU TQFP32
// #30 RXD <--- RXD (SP3232)
// #31 TXD ---> TXD (SP3232)
// #32 PD2/INT0 <--- INTR (TRH031M)
// # 1 PD3/INT1 ---> RST (TRH031M)
// # 2 PD4 ---> D4 (TRH031M)
// # 9 PD5 ---> D5 (TRH031M)
// #10 PD6 ---> D6 (TRH031M)
// #11 PD7 ---> D7 (TRH031M)
// #12 PB0 ---> D0 (TRH031M)
// #13 PB1 ---> D1 (TRH031M)
// #14 PB2 ---> D2 (TRH031M)
// #15 PB3 ---> D3 (TRH031M)
// #16 PB4 ---> CSB (TRH031M)
// #17 PB5 ---> LED
// #23 PC0 ---> A0 (TRH031M)
// #24 PC1 ---> A1 (TRH031M)
// #25 PC2 ---> A2 (TRH031M)
// #26 PC3 ---> ALE (TRH031M)
// #27 PC4 ---> /RD (TRH031M)
// #28 PC5 ---> /WR (TRH031M)
-This is a source of 13.560MHz RFID card reader for TRH031M as ATMEGA8-16AU MPU.
The title is 3Alogics TRH031M 13.56MHz RFID Reader V1.0.
project : RFID Reader V2.0
Target : MEGA8-16AU
Crystal: 16.000 Mhz
Input : TRH031M RFID 13.56MHz
Output : RS232C 115200,N,8,1
Compiler : ICC-AVR V6.26C
// Pin configuration for ATMEGA8-16AU TQFP32
//#30 RXD <--- RXD (SP3232)
//#31 TXD---> TXD (SP3232)
//#32 PD2/INT0 <--- INTR (TRH031M)
//# 1 PD3/INT1---> RST (TRH031M)
//# 2 PD4---> D4 (TRH031M)
//# 9 PD5---> D5 (TRH031M)
//#10 PD6---> D6 (TRH031M)
//#11 PD7---> D7 (TRH031M)
//#12 PB0---> D0 (TRH031M)
//#13 PB1---> D1 (TRH031M)
//#14 PB2---> D2 (TRH031M)
//#15 PB3---> D3 (TRH031M)
//#16 PB4---> CSB (TRH031M)
//#17 PB5---> LED
//#23 PC0---> A0 (TRH031M)
//#24 PC1---> A1 (TRH031M)
//#25 PC2---> A2 (TRH031M)
//#26 PC3---> ALE (TRH031M)
//#27 PC4---> /RD (TRH031M)
//#28 PC5---> /WR (TRH031M)
Platform: |
Size: 12288 |
Author: acleds |
Hits:
Description: PB375 U盘读写汇编程序
性价比超高的U盘读写模块-PB375，兼容CH375读写操作
-PB375 U disk read and write assembler cost-effective ultra-high U-disk read-write module-PB375, read and write compatible with the operation CH375
Platform: |
Size: 646144 |
Author: 肖凤 |
Hits:
Description: 用AVR单片机直接控制其步进电机，c语言写成，用mege8L的PB0-PB3连接步进电机的四个接线端！该步进电机的转矩很小，强烈建议不要将其从底座上拆下！！！否则没有轴承支撑，摩擦力太大，转不起来！-AVR with direct control of its single-chip stepper motor, c language, and PB0-PB3 of mege8L to connect the four stepper motor terminal! The small torque stepper motor, it is strongly recommended not to be removed from the base! ! ! Otherwise there is no bearing support, too much friction, does not turn up!
Platform: |
Size: 1024 |
Author: 张扬 |
Hits:
Description: PB 技巧例资料,关于PB 开发的一些相关技巧-PB skills cases information on the number of PB-related skills development
Platform: |
Size: 2813952 |
Author: wh |
Hits:
Description: AVR单片机教程 pwm控制 ctc模式 PB3输出PWM信号，个人写程序，直接下载，测试pb3就可以用，方便快捷。-AVR microcontroller tutorial mode pwm control ctc PB3 output PWM signal, personal written procedures, direct download, test pb3 you can use, and convenient.
Platform: |
Size: 56320 |
Author: |
Hits: