Welcome![Sign In][Sign Up]
Location:
Search - SJA1000 asm

Search list

[Embeded-SCM DevelopSJA1000驱动程序(C&ASM).rar

Description:
Platform: | Size: 569469 | Author: | Hits:

[Embeded-SCM DevelopSJA1000驱动程序(C&ASM)

Description: SJA1000驱动程序(分别用C&ASM书写)-SJA1000 Driver (respectively 52 Writing)
Platform: | Size: 569736 | Author: 李冰 | Hits:

[assembly languagecan+sja1000

Description: ,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ,RS 接51k电阻到地。 2,SJA1000与82C250的接口,逻辑上为SJA1000输出0(显性位),表现为低点平输出给82C250,则82C250输出 差分的低电平。SJA1000输出1(隐性位),表现为高电平或悬空输出给82C250,则82C250输出悬空状态。 3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。 还有里面定义有接收错误标志码,不知道何时用。
Platform: | Size: 24896 | Author: 叶子 | Hits:

[Embeded-SCM DevelopSJA1000驱动程序(C&ASM)

Description: SJA1000驱动程序(分别用C&ASM书写)-SJA1000 Driver (respectively 52 Writing)
Platform: | Size: 569344 | Author: 李冰 | Hits:

[DSP programCAN2.0

Description: 关于can总线2.0的发送和接受程序,经项目验证通过,具有极大的参考价值.-2.0 on the bus can send and receive procedures, certification by the project, is of great reference value.
Platform: | Size: 51200 | Author: 宋真 | Hits:

[assembly languageSJA1000programe

Description: SJA1000控制器的初始化程序,接收和发送程序-SJA1000 controller initialization procedures, procedures for receiving and sending
Platform: | Size: 2048 | Author: wangxiaobin | Hits:

[assembly languagecan+sja1000

Description: ,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ,RS 接51k电阻到地。 2,SJA1000与82C250的接口,逻辑上为SJA1000输出0(显性位),表现为低点平输出给82C250,则82C250输出 差分的低电平。SJA1000输出1(隐性位),表现为高电平或悬空输出给82C250,则82C250输出悬空状态。 3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。 还有里面定义有接收错误标志码,不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.
Platform: | Size: 24576 | Author: 叶子 | Hits:

[SCMMCU_CAN_SJA1000_PELI_library

Description: 基于MCU的CAN程序库SJA1000_PELI库-MCU based on the CAN library SJA1000_PELI Library
Platform: | Size: 303104 | Author: changliang | Hits:

CodeBus www.codebus.net