Location:
Search - TXD L
Search list
Description: TXD5408 LCD 驱动程序，应该于数码MPM，手机，等数码产品。-TXD5408 LCD driver should be in digital MPM, mobile phones, and other digital products.
Platform: |
Size: 2104320 |
Author: david |
Hits:
Description: /DM430-L型最小系统板串口测试程序，使用单片机的串口0
//通过电脑与串口线连接开发板串口座，使用串口调试助手发送数据到系统板
//系统板会将收到的数据再发送到串口调试助手，接收采用中断模块，发送用查询
//板载的BSL模块可以通过跳线帽设置为USB转串口模式，笔记本电脑没有串口可以直接代替
//开发板的BSL_Config区的RXD和TXD0连接，TXD和RXD0连接即可
调试环境：EW430 V5.30-
English
Spanish
Arabic
/ DM430-L, the minimum system board serial port test program, the use of the microcontroller s serial port 0
//By the computer with serial cable to connect the development board serial port, serial debugging aides to send data to the system board
//System board will receive the data before sending to the serial port debugging assistant, receiving the interrupt module, send inquiries
//Onboard BSL module can be set by jumper cap for the USB to serial mode, the notebook computer does not have the serial port can directly replace the
//Development board BSL_Config area RXD and TXD0 of connection, the TXD and RXD0 connection can be
//Debugging environment: EW430 V5.30
Platform: |
Size: 25600 |
Author: wujunkai |
Hits:
Description: DM430-L型开发板RS485通信实验，通过开发板与电脑进行数据通信，485接在UART1上
电脑端必备RS232转RS485模块，否则无法进行直接的连接RS485之间通过双绞线连接，如果距离近，可以不使用120欧电阻匹配电脑端通过串口调试助手操作，先将数据由电脑发往开发板开发板板会将收到的数据再发送到串口调试助手，接收采用中断模块，发送用查询板载的BSL模块可以通过跳线帽设置为USB转串口模式，笔记本电脑没有串口可以直接代替开发板的BSL区的RXD和TXD0连接，TXD和RXD0连接即可注意使用BSL模块作为USB转串口功能的时候，RTS和TCK跳线帽、DTR和RESET跳线帽要断开波特率更改请通过config.h文件，直接更改baud参数即可-Based on MSP430 485 communication protocol
Platform: |
Size: 24576 |
Author: 邹天胜 |
Hits:
Description: DM430-L型最小系统板串口测试程序，使用单片机的串口0通过电脑与串口线连接开发板串口座，使用串口调试助手发送数据到系统板
//系统板会将收到的数据再发送到串口调试助手，接收采用中断模块，发送用查询
板载的BSL模块可以通过跳线帽设置为USB转串口模式，笔记本电脑没有串口可以直接代替
开发板的BSL_Config区的RXD和TXD0连接，TXD和RXD0连接即可-DM430-L-type minimum system board serial testing procedures, the use of single-chip serial 0 via serial cable to connect the computer and the development board serial seat, using serial debugging assistant to send data to the system board// system board will receive data then sent to the serial debugging assistant, reception using interrupt module, sent by check// BSL-board module can be set by a jumper for the USB to serial mode, the laptop does not have serial ports can directly replacedevelopment board BSL_Config area RXD and TXD0 connection, TXD and is connected to RXD0
Platform: |
Size: 147456 |
Author: 王哲 |
Hits: