Location:
Search - XINT1
Search list
Description: 配置GPIOE为XINT1，XINT2，由于不知道要上载5次，所以一次把五个程序都上载了，现在重新依次上载-GPIOE configuration for XINT1, XINT2, as a result do not know want to upload 5 times, so the first five procedures to upload, and now in order to re-upload
Platform: |
Size: 1024 |
Author: sophia |
Hits:
Description: 2812有三个独立的外部可屏蔽中断XINT1,XINT2,XINT13和一个不可屏蔽中断XNMI，外部扩展可屏蔽中断通过CPLD之后，通过按键产生一外部中断EXINT5。-2812 has three independent external maskable interrupt XINT1, XINT2, XINT13 and a non-maskable interrupt XNMI, external expansion through the CPLD can be screened after the break, produced by an external interrupt button EXINT5.
Platform: |
Size: 240640 |
Author: 蔡全 |
Hits:
Description: TIDSP280x的中断例子程序，包括TIME0、TIME1、TIME2、xint1、xint2，在TIME0中设置GPIO10输出方波-TIDSP280x interrupt example program, including TIME0, TIME1, TIME2, xint1, xint2, in TIME0 set GPIO10 output square wave
Platform: |
Size: 5120 |
Author: 袁生 |
Hits:
Description: 1.本示例演示28035的外中断配置和使用方法。28035一共有3个外中断，这三个外中断的
中断触发源可配置为GPIO0-GPIO31之间的任意一个；本示例中，我便将GPIO27作为XINT1
的中断触发沿，如果按键按下，一个下降沿将触发进入中断，在中断中，我们将让D2的状态
翻转一次；
2.外中断XINT可以配置为上升沿触发，下降沿触，双边触发(上升沿和下降沿都触发)。-1. This sample demonstrates 28035 external interrupt configuration and method of use. 28035 a total of three external interrupt, the three outer interruption
Interrupt trigger source can be configured for GPIO0- between GPIO31 any one This example, and I will GPIO27 as XINT1
The interruption of the trigger, if key press, a falling edge will trigger into interrupt, in interrupt, we will make the state of D2
Turn over one time.
2. External interrupt XINT can be configured to rising edge trigger, falling edge contact, bilateral trigger (rising edge and falling edge are trigger).
Platform: |
Size: 716800 |
Author: 卢启明 |
Hits:
Description: DSPTMS320f2812的有关外部中断的小程序.主要实现利用外部中断XINT1实现当按键按下后流水灯实现全亮，流水灯是利用CPU时钟中断实现1s定时闪烁。-About the external interrupt DSPTMS320f2812 small program mainly realize XINT1 achieved when using an external interrupt light water after the button is pressed to achieve full brightness, light water is the use of the CPU clock timer interrupt achieve 1s blink.
Platform: |
Size: 156672 |
Author: lily |
Hits:
Description: 编写TMS320LF2407的对SCI模块、SPI模块、EV中通用定时器（T1、T2、T3、T4）及捕捉逻辑（CAP1\CAP2\CAP3)、外部中断引脚（XINT1、XINT2）和CAN模块初始化程序。-Prepared for SCI module, SPI module, EV in general-purpose timer (T1, T2, T3, T4) and capture logic (CAP1 \ CAP2 \ CAP3), TMS320LF2407 external interrupt pins (XINT1, XINT2) and CAN module initialization procedure.
Platform: |
Size: 4096 |
Author: 刘梦雅 |
Hits:
Description: 本程序用来测试DSP外部中断，把GPIO0、GPIO1分别设为外部中断1（Xint1）和外部中断2（Xint2），两个其他GPIO 分别作为中断的触发信号，完成中断触发。程序运行时，可以观察相应变量的变化。-This procedure is used to test the DSP external interrupt, the GPIO0, GPIO1 were set to external interrupt 1 (Xint1) and external interrupt 2 (Xint2), respectively, as the two other GPIO interrupt trigger signal, complete interrupt is triggered. The program is running, you can observe the changes in the corresponding variable.
Platform: |
Size: 2007040 |
Author: 张玉龙 |
Hits: