Search - dc machine

Search - dc machine - List

[Other resource] dianjicesu DL : 0: 单片机开发实验，在C8051F020平台下，用以直流电机测速，并在七段数码管上显示出来。-MCU Development experiment, the C8051F020 platform for the DC machine guns, in paragraph 107 of digital tube displayed.
Update : 2008-10-13 Size : 68.9kb Publisher : dym
[Other resource] dianjicesu1 DL : 0: 单片机开发程序，用以直流电机测速，并把所得值在七段数码管上显示出来。-MCU development process for the DC machine guns, and the values obtained in paragraph 107 of digital tube displayed.
Update : 2008-10-13 Size : 3.83kb Publisher : dym
[assembly language] ZLDJ DL : 0: 直流电机的程序代码-DC machine code
Update : 2008-10-13 Size : 808byte Publisher : 田磊
[assembly language] ZLDJ DL : 0: 直流电机的程序代码-DC machine code
Update : 2025-02-19 Size : 1kb Publisher : 田磊
[SCM] dianjicesu DL : 0: 单片机开发实验，在C8051F020平台下，用以直流电机测速，并在七段数码管上显示出来。-MCU Development experiment, the C8051F020 platform for the DC machine guns, in paragraph 107 of digital tube displayed.
Update : 2025-02-19 Size : 69kb Publisher : dym
[Other] Modeling[1].and.High.Performance.Control.of.Elect DL : 0: This book is intended to be an exposition of the modeling and control of electric machines, specifically, the direct current (DC) machine and the alternating current (AC) machines consisting of the induction motor, the permanent magnet (PM) synchronous motor, and the brushless DC motor. The particular emphasis here is on techniques used for high-performance applications, that is, applications that require both rapid and precise control of position, speed, and/or torque. Traditionally, DC motors were reserved for high-performance applications (positioning systems, rolling mills, traction drives, etc.) because of their relative ease of control compared to AC machines. However, with the advances in control methods, computing capability, and power electronics, AC motors continue to replace DC motors in high-performance applications. The intent here is to carefully derive the mathematical models of the AC machines and show how these mathematical models are used to design control algorithms
Update : 2025-02-19 Size : 23.51mb Publisher : kumar
[matlab] untitled DL : 0: its about Dc machine and can use for other kind of machine
Update : 2025-02-19 Size : 6kb Publisher : ali
[matlab] power_brushlessDCmotor DL : 1: A three-phase motor rated 1 kW, 500 Vdc, 3000 rpm is fed by a six step voltage inverter. The inverter is a MOSFET bridge of the SimPowerSystems™ library. A speed regulator is used to control the DC bus voltage. The inverter gates signals are produced by decoding the Hall effect signlas of the motor. The three-phase output of the inverter are applied to the PMSM block s stator windings. The load torque applied to the machine s shaft is first set to 0 and steps to its nominal value (11 N.m) at t = 0.1 s. Two control loops are used. The inner loop synchronises the inverter gates signals with the electromotive forces. The outer loop controls the motor s speed by varying the DC bus voltage. -A three-phase motor rated 1 kW, 500 Vdc, 3000 rpm is fed by a six step voltage inverter. The inverter is a MOSFET bridge of the SimPowerSystems™ library. A speed regulator is used to control the DC bus voltage. The inverter gates signals are produced by decoding the Hall effect signlas of the motor. The three-phase output of the inverter are applied to the PMSM block s stator windings. The load torque applied to the machine s shaft is first set to 0 and steps to its nominal value (11 N.m) at t = 0.1 s. Two control loops are used. The inner loop synchronises the inverter gates signals with the electromotive forces. The outer loop controls the motor s speed by varying the DC bus voltage.
Update : 2025-02-19 Size : 12kb Publisher : jurifa
[matlab] dc_motor DL : 0: 利用Matlab 的Simulink工具箱设计一个控制系统框图，本设计的主要内容是双闭环直流电机调速系统的动态结构框图，本设计基于大学本科“电机拖动与运动控制”课程中双闭环直流电机调速系统的模型设计，建模仿真结果与教材理论分析结果相同。-Use of Matlab Simulink toolbox to design a control system block diagram of this design is the dynamic structure of the dual closed loop DC motor speed control system block diagram, the design is based on the curriculum of undergraduate motor drive and exercise control "dual closed loop DC machine tunespeed system model design, modeling and simulation results and textbook theory analysis results are the same.
Update : 2025-02-19 Size : 7kb Publisher : 王小兵
[matlab] DC-Machine DL : 0: This a matlab m-file for simulating a shunt dc machine and plot important curves.-This is a matlab m-file for simulating a shunt dc machine and plot important curves.
Update : 2025-02-19 Size : 1kb Publisher : ali
[Energy industry] dc-mc DL : 0: this model simply a shows the variation of dc machine torque and speed when supplied by controlled rectifier in open loop.
Update : 2025-02-19 Size : 9kb Publisher : ashish
[LabView] dc DL : 0: SIMULATION A DC MACHINE WITH USING MATLAB
Update : 2025-02-19 Size : 9kb Publisher : ghahraman
[Energy industry] dc machine DL : 0: how to use dc machine in pscad
Update : 2025-02-19 Size : 34kb Publisher : Rajer
[matlab] fwdplaning DL : 0: DC machine controllers
Update : 2025-02-19 Size : 79kb Publisher : mistrale
[matlab] DC-MOTOR DL : 0: dc machine control implimentationg using pid
Update : 2025-02-19 Size : 315kb Publisher : mistrale
[Other] CH02- CMD Machine CC DL : 0: dc machine control using fuzzy logoc
Update : 2025-02-19 Size : 417kb Publisher : mishak
[Other] matlab dc-motor-speed-control DL : 0: dc machine model using simulink matlab
Update : 2025-02-19 Size : 122kb Publisher : mishak
[Books] Machine & Drive DL : 0: machine drive reference for second year students in Engineering
Update : 2025-02-19 Size : 13.55mb Publisher : alfareh
[SCM] DC_Machine_Speed_Control DL : 0: 使用Simplorer实现直流电机速度控制，珍贵(DC Machine control fullfillment using simplorer software)
Update : 2025-02-19 Size : 22kb Publisher : innovation
[Other systems] A Simpler Approach to the Modelling of Permanent Magnet Brushless DC Machine in MATLAB Environment DL : 0: A Simpler Approach to the Modelling of Permanent Magnet Brushless DC Machine in MATLAB Environment
Update : 2019-08-25 Size : 878.23kb Publisher : mehdi_hb_2019

« 12 3 4 5 6 7 8 »