Location:
Search - msp430f149 n
Search list
Description: msp430f149单片机与nrf905串口通信，这是发送节点的c语音程序-msp430f149 MCU and nrf905 serial communication, which is sending node c voice procedures
Platform: |
Size: 28672 |
Author: 姜鹏 |
Hits:
Description: msp430f149,用指针方式，MCU不停向PC机发送数据,在屏幕上显示 hello,welcome my MCU office.\n/I like MCU.-Msp430f149, with pointer way, keep sending to PC MCU data, displayed on the screen, hello backgound of MCU office. \ n wish/I like MCU.
Platform: |
Size: 16384 |
Author: 刘齐成 |
Hits:
Description: IAR环境下的MSP430F149，以温度传感器的电压值为采样信号的AD采样程序，采样间隔为80ms。- Description: Use ADC12 and the integrated temperature sensor to detect
temperature gradients. The temperature sensor output voltage is sampled
~ every 80ms and compared with the defined delta values using an ISR.
(ADC12OSC/256)/ determines sample time which needs to be greater than
30us for temperature sensor.
ADC12 is operated in repeat-single channel mode with the sample and
convert trigger sourced from Timer_A CCR1. The ADC12MEM0_IFG at the end
of each converstion will trigger an ISR.
ACLK = n/a, MCLK = SMCLK = default DCO ~ 800k, ADC12CLK = ADC12OSC
// MSP430F149
// -----------------
// /|\| XIN|-
// | | |
// --|RST XOUT|-
// | |
// |A10 P3.4|-->LED
Platform: |
Size: 21504 |
Author: 山雨 |
Hits:
Description: IAR环境下的MSP430F149，使用定时器A，每隔5000个时钟周期点亮/熄灭LED的程序- Description: Toggle P3.4 using software and TA_0 ISR. Toggles every
50000 SMCLK cycles. SMCLK provides clock source for TACLK.
// During the TA_0 ISR, P3.4 is toggled and 50000 clock cycles are added to
CCR0. TA_0 ISR is triggered every 50000 cycles. CPU is normally off and
used only during TA_ISR.
ACLK = n/a, MCLK = SMCLK = TACLK = default DCO ~800kHz
// MSP430F149
// ---------------
// /|\| XIN|-
// | | |
// --|RST XOUT|-
// | |
// | P3.4|-->LED
Platform: |
Size: 19456 |
Author: 山雨 |
Hits:
Description: IAR环境下的MSP430F149，使用定时器A的累加模式计时，每当CCR0溢出时，点亮/熄灭LED。- Description: Toggle P3.4 using software and TA_0 ISR. Timer_A is
configured for up mode, thus the timer overflows when TAR counts
to CCR0. In this example, CCR0 is loaded with 20000.
ACLK = n/a, MCLK = SMCLK = TACLK = default DCO ~800kHz
// MSP430F149
// ---------------
// /|\| XIN|-
// | | |
// --|RST XOUT|-
// | |
// | P3.4|-->LED
Platform: |
Size: 15360 |
Author: 山雨 |
Hits:
Description: 硬件平台MSP430F149单片机，用于采集N路光伏电池电流和电压，便于实时监控。-The MSP430F149 microcontroller hardware platform for the acquisition of N-way of photovoltaic battery current and voltage, to facilitate real-time monitoring.
Platform: |
Size: 34816 |
Author: gump |
Hits:
Description: 使用MSP430F149芯片，透过串口给电脑发送数据，波特率9600,8数据，无校验，。发送的数据先是 MCU sends 0~127 to PC and the\\n screen will display their corresponding\\n ASCII code as follows:然后是01234567890123456789abcdefgh......,每发送一个数据回车一次-MSP430F149 chip to send data to the computer through the serial port baud rate 9600 data, no parity. Send the data first MCU sends 0 ~~ 127 to a PC and the \ \ n screen will display their corresponding \ \ n ASCII code as follows: Then 01234567890123456789abcdefgh ...... each send a carriage return
Platform: |
Size: 24576 |
Author: 超越 |
Hits: