Location:
Search - sd data logger
Search list
Description: This demo uses the selected hardware platform as an SD card reader. Connect the hardware platform to a computer through a USB cable.
To run this project, you will need to load the corresponding firmware into the devices. There are two methods available for loading the demos: Precompiled demos and source code projects.
Precompiled Demos are available in the “\USB – Precompiled Demos” folders. Each demo should be prefaced with the hardware platform it is compiled for. Select the file that matches the hardware that you have and the demo that you want to run. For more information about how to load a precompiled project, please see the “Getting Started – Loading a precompiled demo” guide.
The source code for this demo is available in the “Topics…->MPLAB IDE).
Please note that when using either the C30 or C32 demo projects you will be required to select the correct processor for the demo board.
1) Open the associated project file
2) In MPLAB Select “Configure->Select Device”
3) In the device list box in the top left corner of that window, select the desired device.
NOTE WHEN USING THE HID BOOTLOADER (for PIC18F87J50 PIM): The “USB Device - Mass Storage - SD Card reader” and “USB Device - Mass Storage - SD Card data logger” demos make use of the SD Card PICtail Daughter Board (Microchip® Direct: AC164122). This PICtail uses the RB4 I/O pin for the card detect (CD) signal, and is actively driven by the PICtail. The active drive overpowers the pull up resistor on the RB4 pushbutton (on the PIC18F87J50 FS USB Plug-In Module board). As a result, if the PIC18F87J50 is programmed with the HID bootloader, and an SD Card is installed in the socket when the microcontroller comes out of reset, the firmware will immediately enter the bootloader (irrespective of the RB4 pushbutton state). To exit the bootloader firmware, remove the SD Card from the SD Card socket, and tap the MCLR button. When the SD Card is not plugged in, the PICtail will drive the card detect signal (which is connected to RB4) logic high, which will enable the bootloader to exit to the main application after coming out of reset. Once the main application firmware is operating, the SD Card can be plugged in. The SD Card is “hot-swappable” and should be recognized by the host upon insertion. To avoid this inconvenience when using the bootloader with the PICtail, it is suggested to modify the bootloader firmware to use some other I/O pin for bootloader entry, such as RB0 (which has a pushbutton on it on the HPC Explorer board).
Platform: |
Size: 773398 |
Author: bluntpig |
Hits:
Description: sd card interface for data logger
Platform: |
Size: 2048 |
Author: imran |
Hits:
Description: USB Device - Mass Storage - SD Card data logger
Platform: |
Size: 145408 |
Author: knsitu |
Hits:
Description: 本代码为数据记录仪的代码及原理图，代码编译通过，数据记录仪为8通道温度、8通道电压、8通道电流采集数据记录于SD卡中，以mege8535 单片机，AVR-GCC平台。对正在开数据记录仪的朋友绝对是一份不错的资料。-This code is the code for the data logger and the schematic diagram, the code compile data for the 8-channel temperature logger, 8-channel voltage, 8-channel current data collection recorded in SD card to mege8535 microcontroller, AVR-GCC platforms. Data logger is being opened on a friend is definitely a good information.
Platform: |
Size: 199680 |
Author: ssbbai |
Hits:
Description: data-logger use the data from pic to store it in SD card memory using the MikroC source code this is the first version which is not guaranteed thnks a lot
Platform: |
Size: 2048 |
Author: nass |
Hits:
Description: Complete GPS Datalogger Project using PIC16F690. It uses a standard SD CARD in SPI mode as the memory to store the GPS data. Does not uses a FAT File System though.
Platform: |
Size: 952320 |
Author: Sougata Das |
Hits:
Description: 基于MSP430和MicroSD卡的GPS记录器
MSP430f149接收C3-370模块GPS信号，用Nokia5110液晶显示经纬度，并将$GPRMC语句后62字节保存在Micro SD卡上。所存数据读入电脑后可通过RouteConverter.exe软件转成KML文件，加载到google earth后可以显示轨迹。
资料包括
原理图：Altium Designer Winter 09 格式和PDF格式
控制程序：基于MSP430F149的GPS记录程序。主要完成坐标显示、迹记录等功能。
整理时间：
下午 07:10 2012-3-6 沨-MSP430 and MicroSD card-based GPS logger
MSP430f149 receive the GPS signal of the C3-370 module, with Nokia5110 liquid crystal display latitude and longitude, and $ GPRMC statement after the 62 bytes stored on the Micro SD card. The stored data is read into a computer through RouteConverter.exe software can turn into a KML file is loaded into google earth can show the trajectory.
Information, including
Schematic: of Altium Designer Winter 09 and PDF formats, the required components package library
Control procedures: MSP430F149 GPS records program. Complete the coordinate display, track records.
Finishing time:
7:10 PM 2012-3-6 Phoenix
Platform: |
Size: 347136 |
Author: HuNB |
Hits:
Description: 設計給高端GNSS/GPS 用的原始資料紀錄器(RAW DATA)，可記錄衛星觀測資料達50HZ 以上，已於Trimbel BD-970 + Arduino + SD Shield 上面測試。-This Data logger code is used for logging high update rate GNSS/GPS engine board. It can reach 50Hz update rate on Arduino ATMEGA328+ SD Card Shield.
Platform: |
Size: 1624064 |
Author: Allen Lin |
Hits:
Description: stm32f103 data logger with fille systeme on sd( sdio) this exemple store frequencie and voltage ,
it also use timer rtc adc led gpio.-stm32f103 data logger with fille systeme on sd( sdio) this exemple store frequencie and voltage ,
it also use timer rtc adc led gpio.
Platform: |
Size: 16025600 |
Author: guilllaume |
Hits:
Description: This is a source code for digital data logger using PIC micro-controller
Platform: |
Size: 30720 |
Author: sadii
|
Hits: