Location:
Search - stellaris usb
Search list
Description: TI Stellaris系列（原Luminary）公司的USB协议栈源码-TI Stellaris family (formerly Luminary) the company' s USB protocol stack source code
Platform: |
Size: 1496064 |
Author: ygchaoren |
Hits:
Description: 基于《Stellaris外设驱动库》的例程：处理器直接触发ADC采样
本实验演示配置ADC采样序列0，通过处理器直接触发ADC采样，ADC模拟量需从外部输入（ADC0），最大不能超过3.0V，因为ADC内置的参考电压为3.0V。
在进行ADC配置之前，必须首先进行PLL锁相环配置（详见EasyARM1138例程\02 SysCtl(系统控制)\3 锁相环PLL设置）。错误配置PLL将使系统进入异常。
ADC采样得到的数字量将利用超级终端从串口读出 。本开发板采用USB虚拟串口UART2,一般很多串口调试助手都不支持，所以建议使用WINDOWS系统自带的超级终端。-Based on " Stellaris peripheral driver library" of routines: Processor direct trigger ADC sampling configuration in this experiment demonstrates ADC sampling sequence 0, through the processor directly to trigger ADC sampling, ADC analog input required from the outside (ADC0), the largest not more than 3.0 V, because the ADC internal reference voltage of 3.0V. During ADC configuration, you must first be phase-locked loop PLL configuration (see EasyARM1138 routines \ 02 SysCtl (system control) \ 3 phase-locked loop PLL setting). Error Configuring PLL enables the system into the abnormal. ADC sampling by the digital terminal will use the super-read from the serial port. The development board with USB virtual serial port UART2, assistant general do not support a lot of serial debugging, it is proposed to use WINDOWS system comes with HyperTerminal.
Platform: |
Size: 43008 |
Author: 小强 |
Hits:
Description:
Stellaris® Evaluation Kit for Keil RealView®
MDK
The Stellaris® Evaluation Kits provide a low-cost way to start designing with Stellaris
microcontrollers using Keil’s RealView Microcontroller Development Kit (MDK) for ARM
controllers. The Evaluation Board (EVB) can function as either a complete evaluation target,
or as a debugger interface to any external Stellaris device. The included USB cable is all that
is needed to provide power and communication to the host PC. -
Stellaris® Evaluation Kit for Keil RealView®
MDK
The Stellaris® Evaluation Kits provide a low-cost way to start designing with Stellaris
microcontrollers using Keil’s RealView Microcontroller Development Kit (MDK) for ARM
controllers. The Evaluation Board (EVB) can function as either a complete evaluation target,
or as a debugger interface to any external Stellaris device. The included USB cable is all that
is needed to provide power and communication to the host PC.
Platform: |
Size: 508928 |
Author: sivar22 |
Hits:
Description: This fascinating eye-tracking system was developed with an EKK-LM3S9B96 evaluation board and a USB camera. The Stellaris MCU works as a USB host and controls the camera. A button on the board is for switching the calibration/tracking modes. In Calibration mode, a captured eye image with detected markers is displayed on a computer screen. In the Tracking mode, gaze points are plotted on a white image. Results can be monitored by multiple PCs on a network
Platform: |
Size: 1409024 |
Author: ahmed |
Hits:
Description: This example application demonstrates using a USB
Communications Device Class for hosting a FTDI FT232R device.
I m using FTDIs UB232R development module:
http://apple.clickandbuild.com/cnb/shop/ftdichip?op=catalogue-products-null&prodCategoryID=58&title=UB232R
Which has this FTDI chip:
http://www.ftdichip.com/Products/ICs/FT232R.htm
It has USB_CLASS_VEND_SPECIFIC (0xff) Interface Class.
Other CDC drivers could also be added to this example in the future (ACM, Prolific,...).
Platform: |
Size: 374784 |
Author: sampi |
Hits:
Description: Stellaris CDC ACM Example. It is not a a fully functional example, just usblib and application that works with CDC ACM.
Platform: |
Size: 1311744 |
Author: sampi |
Hits:
Description: 介绍使用Stellaris的USB处理器进行USB主机开发-Introduced using the Stellaris USB processor USB host development
Platform: |
Size: 360448 |
Author: chenzhenlei |
Hits:
Description: ek-lm4f120xl TI Stellaris LaunchPad 例程之串口回传-This example application utilizes the UART to echo text. The first UART
(connected to the USB debug virtual serial port on the evaluation board)
will be configured in 115,200 baud, 8-n-1 mode. All characters received on
the UART are transmitted back to the UART.
Platform: |
Size: 139264 |
Author: 123 |
Hits: