Location:
Search - stm32 TIM1 PWM
Search list
Description: STM32定时器PWM输入捕获，利用TIM1计算脉冲频率及占空比。-This example shows how to use the TIM peripheral to measure the frequency and duty cycle of an external signal.
Platform: |
Size: 8192 |
Author: 梁凯 |
Hits:
Description: STM32的PWM输出模式，STM32的TIM1模块是增强型的定时器模块，天生就是为电机控制而生，可以产生3组6路PWM，同时每组2路PWM为互补，并可以带有死区，可以用来驱动H桥。-STM32' s PWM output mode, STM32' s TIM1 module is enhanced timer module, is inherently for the motor control, it can produce three groups 6-channel PWM, while the complementary PWM each 2-way, and can be with the dead zone, can be used to drive H-bridge.
Platform: |
Size: 1024 |
Author: omega |
Hits:
Description: STM32奋斗板-TIM1的PWM演示 可以进行修改，并在通类型开发板上运动-STM32 PWM hard board-TIM1 the presentation can be modified, and in the sports development board through the type
Platform: |
Size: 356352 |
Author: haha |
Hits:
Description: 通过对 TIM1 定时器进行控制，使之各通道输出插入死区的互补PWM 输出，
各通道输出频率均为17.57KHz。
其中，通道1 输出的占空比为50 ，通道2 输出的占空比为25 ，通道3 输
出的占空比为12.5 。各通道互补输出为反相输出。
TIM1 定时器的通道1 到3 的输出分别对应PA.08、PA.09、PA.10 引脚，而通
道1 到3 的互补输出分别对应PB.13、PB.14 和PB.15 引脚，将这些引脚分别接
入示波器正接线，GND 引脚接示波器负接线，在示波器上看到了相应通道占空比
的PWM 输出。-By TIM1 timer control, so that the output of each channel into the dead zone of complementary PWM output, the output frequency of each channel are 17.57KHz. Among them, the channel 1 output 50 duty cycle, channel 2 output 25 duty cycle, channel 3 output duty cycle of 12.5 . The channel output is inverted complementary output. TIM1 timer channel 1 to 3 of the output corresponding to PA.08, PA.09, PA.10 pin, while channels 1 to 3 correspond to the complementary output PB.13, PB.14 and PB.15 pin, These pins are an oscilloscope is wiring, GND pin is connected to the negative terminal oscilloscope, the oscilloscope channel to see the corresponding PWM output duty cycle.
Platform: |
Size: 434176 |
Author: jo |
Hits:
Description: a)目的：基础PWM输入也叫捕获，以及中断配合应用。使用前一章的输出管脚PB1（19脚），直接使用跳线连接输入的PA3（13脚），配置为TIM2_CH4，进行实验。
b)对于简单的PWM输入应用，暂时无需考虑TIM1的高级功能之区别，按照目前我的应用目标其实只需要采集高电平宽度，而不必知道周期，所以并不采用PWM输入模式，而是普通脉宽捕获模式。
-A) purpose: basic PWM input also called capture, and interrupt cooperate to apply. Before using a chapter of the output tube feet PB1 (19 feet), direct use of jump line join input PA3 (13 feet), configuration for the TIM2_CH4, the experiment.
B) for simple PWM input application, temporarily without thinking about the difference between the TIM1 advanced features, according to current my application target in fact only need to collect high level width, which do not need to know the cycle, so not using PWM input mode, but ordinary pulse width capture mode.
Platform: |
Size: 52224 |
Author: zhangxiansheng |
Hits:
Description: STM32 TIM1 PWM 两路输出，带死区时间-STM32 TIM1 PWM two outputs with dead time
Platform: |
Size: 942080 |
Author: sun |
Hits:
Description: 利用STM32高级定时器，产生互补的两路PWM，有完整注释，测试通过-Advanced timers using STM32, resulting in two complementary PWM, with complete notes, test
Platform: |
Size: 418816 |
Author: 虫子 |
Hits:
Description: 这个是STM32的PWM输出模式，STM32的TIM1模块是增强型的定时器模块，下面的代码，是利用TIM1模块的1、2通道产生一共4路PWM的代码例子，类似代码也可以参考ST的固件库中相应example-This is the PWM output mode of the STM32, the STM32 TIM1 module is the enhanced timer module, the following code, TIM1 module 1,2 channel to produce a total of 4 PWM code examples, similar code can also refer to the ST s firmwarethe corresponding example in the library
Platform: |
Size: 1024 |
Author: 陈立 |
Hits:
Description: 基于STM32 TIM1产生占空比渐变的PWM波，开发环境为keil，程序工程完整，注释清楚。-Wave PWM duty cycle gradient based STM32 TIM1 development environment for keil, process engineering complete, clear annotation.
Platform: |
Size: 486400 |
Author: cxx |
Hits:
Description: 基于STM32的TIM1定时器的PWM呼吸灯例程，三通道输出可调-
Based on the STM32 TIM1 PWM timer lamp breathing routines.
Three-channel output adjustable
Platform: |
Size: 3426304 |
Author: troylee |
Hits:
Description: 基于STM32单片机，利用单片机定时器，实现PWM的输出-Based on STM32 microcontroller, using SCM timer for PWM output
Platform: |
Size: 55296 |
Author: 李畅 |
Hits:
Description: 搞定_ STM32 TIM1输出互补波形 加 详细中文注释(STM32 output complementary PWM wave)
Platform: |
Size: 2118656 |
Author: 北斗gq
|
Hits:
Description: 基于STM32单片机设计的高级定时器TIM1的6路互补带死区的PWM输出实验，代码中含有详细的注释，对学习PWM很有帮助(STM32 microcontroller based design of advanced timer, TIM1 6 complementary band, dead zone PWM output experiment, the code contains detailed notes, helpful for learning PWM)
Platform: |
Size: 7658496 |
Author: 傅昌龙
|
Hits:
Description: STM32单片机通用定时器PWM输出实验---含详细注释，对学习STM32定时器PWM输出有帮助(STM32 microcontroller based design of advanced timer, TIM1 6 complementary band, dead zone PWM output experiment, the code contains detailed notes, helpful for learning PWM)
Platform: |
Size: 1984512 |
Author: 傅昌龙
|
Hits:
Description: The timer can be used to generate PWM output. Advanced setting The timer TIM1 and TIM8 can generate up to 7 PWM outputs simultaneously. And universal timers can produce up to 4 at the same time PWM output of the road(In order for the STM32 general timer TIMx to produce PWM output, except for the registers introduced in the previous chapter, we will 3 registers are used to control the PWM. The three registers are the capture / compare mode register (TIMx_CCMR1/2) capture / compare enable registers (TIMx_CCER) and capture / compare registers (TIMx_CCR1~4).)
Platform: |
Size: 308224 |
Author: 多吃点
|
Hits:
Description: STM32 TIM1的PWM输出演示例程。。。。。。。。(STM32 TIM1-PWM output example......)
Platform: |
Size: 983040 |
Author: witliss
|
Hits:
Description: 程序初始化了定时器1，并通过DMA传输修改PWM占空比，方便用来实现快速SPWM(Program initialization timer 1, and through the DMA transmission, modify the PWM duty cycle, easy to use to achieve fast SPWM)
Platform: |
Size: 1024 |
Author: 暮霭
|
Hits:
Description: 通过TIM1的PWM的占空比来控制灯的亮暗程度(Control the brightness of the light by the duty ratio of the TIM1's PWM)
Platform: |
Size: 4055040 |
Author: 新手一枚
|
Hits:
Description: STM32利用高级定时器TIM1，产生4路PWM波，并且波形两两互补(STM32 uses the advanced timer TIM1 to produce 4 PWM waves, and the waveform is 22 complementing.)
Platform: |
Size: 1657856 |
Author: 米斯特俞 |
Hits:
Description: stm32F103 TIM1输出7路PWM
STM32F103ZET6总共有8个定时器，TIM1和TIM8是高级控制定时器，TIM2、3、4、5是通用定时器，
TIM6和TIM7是基本定时器。
本例程实现高级控制定时器TIM1总共7个功能引脚输出PWM波形。(STM32F103ZET6 has 8 timers in total, TIM1 and TIM8 are advanced control timers.
This routine implements an advanced control timer TIM1 that outputs PWM waveforms for a total of 7 function pins.)
Platform: |
Size: 420864 |
Author: 范梵 |
Hits: