Location:
Search - usb_232
Search list
Description: usb_232（仅枚举）-usb_232 (only Enumeration)
Platform: |
Size: 176436 |
Author: 润东 |
Hits:
Description: 这是一个硬件的开发实例，是USB到串口的轮换实例。-This is an example of the development of hardware, USB to Serial examples of the rotation.
Platform: |
Size: 1140614 |
Author: 混世魔王 |
Hits:
Description: usb_232（仅枚举）-usb_232 (only Enumeration)
Platform: |
Size: 176128 |
Author: 润东 |
Hits:
Description: 这是一个硬件的开发实例，是USB到串口的轮换实例。-This is an example of the development of hardware, USB to Serial examples of the rotation.
Platform: |
Size: 1140736 |
Author: 混世魔王 |
Hits:
Description: USB串口驱动 PL类型USB串口Windows驱动-USB serial port driver PL type USB serial Windows driver
Platform: |
Size: 1718272 |
Author: ycd |
Hits:
Description: STM32下做的usb转RS232程序，有兴趣的同志可以参考下，开发板为MCBSTM32-STM32 done under the usb to RS232 procedures comrades are interested can refer to, the development board for MCBSTM32
Platform: |
Size: 326656 |
Author: wang ping |
Hits:
Description: 一个不错的usb_232驱动程序，可以解决您本本无串口的困扰-Usb_232 a good driver, you can solve your non-serial books plagued
Platform: |
Size: 243712 |
Author: 李岩 |
Hits:
Description: 实验器材:
战舰STM32F103开发板V3版本
实验目的:
学习串口的使用(接收与发送)
硬件资源:
1,DS0(连接在PB5)
2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面)
实验现象:
本实验,STM32通过串口1和上位机对话，STM32在收到上位机发过来的字符串(以回车换
行结束)后， 原原本本的返回给上位机。下载后，DS0闪烁，提示程序在运行，同时每
隔一定时间，通过串口1输出一段信息到电脑。
注意事项:
1,电脑端串口调试助手波特率必须是115200.
2,请使用XCOM/SSCOM串口调试助手,其他串口助手可能控制DTR/RTS导致MCU复位/程序不运行
3,串口输入字符串以回车换行结束.
4,请用USB线连接在USB_232,找到USB转串口后测试本例程.
5,P4的PA9/PA10必须通过跳线帽连接在RXD/TXD上.
-Experimental equipment: Battleship STM32F103 Development Board V3 version Purpose: Learning to use the serial port (receive and transmit) hardware resources: 1, DS0 (connected to PB5) 2, 1 serial port (baud rate: 115200, PA9/PA10 connections onboard USB to serial chip CH340 above) experimental phenomena: this experiment, STM32 through the serial port 1 and PC dialogue, STM32 after a string sent the host computer (the end with a carriage return line feed) received exactly back to the host computer. After downloading, DS0 flashes, indicating the program is running, but at a certain time, a piece of information through the serial port 1 output to the computer. Note: 1, computer terminal serial debugging assistant baud rate must be 115,200.2, please use the XCOM/SSCOM serial debugging assistant, other serial Assistant may control DTR/RTS cause MCU reset/program does not run 3, serial input string End carriage return line feed. 4, connect the USB cable in USB_232, find a USB-to-serial test
Platform: |
Size: 2122752 |
Author: 吴宇轩 |
Hits: