Location:
Search - wirless
Search list
Description: 一款用j2me做的手机游戏，测试平台事xp，j2me wirless toolkit-J2ME do with one phone games to test things xp platform, J2ME edge toolkit
Platform: |
Size: 84970 |
Author: 龙焕 |
Hits:
Description: 一款用j2me做的手机游戏，测试平台事xp，j2me wirless toolkit-J2ME do with one phone games to test things xp platform, J2ME edge toolkit
Platform: |
Size: 84992 |
Author: 龙焕 |
Hits:
Description: 利用VC_开发无线数据采集软件.pdf
利用串口和modem进行开发的介绍。-VC_ the development of the use of wireless data acquisition software. Pdf using serial port and modem development of the introduction.
Platform: |
Size: 1295360 |
Author: redyjq |
Hits:
Description: contains pdf documents for MIMO in wirless communications, MI_NLMS adaptive beamforming algorithm for OFDM system, narrowband beamforming algorithm for smart antenna
Platform: |
Size: 3358720 |
Author: empress |
Hits:
Description: 一个通过接收无线信号进行工作的源码,通过四位的4000米无线模块传输，传输可加密-A wireless signal through the wirless.
Platform: |
Size: 3072 |
Author: 耿峰 |
Hits:
Description: wlan tenique for scheduler wirle-wlan tenique for scheduler wirless
Platform: |
Size: 31609856 |
Author: p |
Hits:
Description: 设计2.4GHz的短距离无线传输天线的资料-The data for designing 2.4GHz SRD wirless antenna
Platform: |
Size: 6663168 |
Author: vingal |
Hits:
Description: kalman filter matlab tool help full for understanding the coding for the kalmanfilter, which can either be used for any purposes which could be help for digital signal processing, wirless mobile communication , OFDM .
Platform: |
Size: 7168 |
Author: Sk. Khajarasool |
Hits:
Description: Wirless ATMEGA Application with c source code
and schematics
Platform: |
Size: 503808 |
Author: Dori_leroi |
Hits:
Description: comparaison between MAC for wirless network sensor
Platform: |
Size: 241664 |
Author: james |
Hits:
Description: MHEED protocol for wirless network sensor
Platform: |
Size: 169984 |
Author: james |
Hits:
Description: OFDM for wirless communication
Platform: |
Size: 11658240 |
Author: Sonali |
Hits:
Description: some articles about Wirless sensor web
Platform: |
Size: 521216 |
Author: leondeom |
Hits:
Description: C6000 dsp 无线通信 mcbsp 代码-C6000 dsp wirless communication mcbsp code
Platform: |
Size: 6144 |
Author: laohai |
Hits:
Description: E-books security in wirless network
Platform: |
Size: 3347456 |
Author: Samir |
Hits:
Description: 1000 circuit design in wirless and other
Platform: |
Size: 2449408 |
Author: amoa |
Hits:
Description: a program ablout wirless network
Platform: |
Size: 525312 |
Author: vahid |
Hits:
Description: 1 操作说明：
根据提示输入三位编码（编码不大于255），可以按N键删除编码，按Y键确认，再按UP键为上行，按DOWN键为下行，按S键，为停止。再次按N键为删除编码，可重新输入其它编码进行其它灯的控制。
注：仿真中显示画面是倒着的。
2 用途：
此遥控器用来作智能升降机遥控升降用，当然也可以改成其它用途，整机用锂电池供电，采用专用的无线收发模块，显示用12864点阵液晶显示。有效控制距离，50m左右，欢迎大家欣赏！
3 打开仿真文件，直接运行即可看到显示画面。本仿真软件用的是protues7.5版本的。-1 Instructions:
According prompted three encoding (encoding is not greater than 255), you can press N key to delete the code, press Y button to confirm, then press UP key for uplink, press DOWN key is down, press S key to stop. Press N key again to remove code, may re-enter the other codes for other lighting control.
Note: The simulation of the display is backwards.
Two purposes:
The remote control is used to make intelligent lifts with the remote control lifting, of course, can also be changed to other uses, lithium battery-powered machine, using a dedicated wireless transceiver modules, dot-matrix LCD display with 12864. Effective control of the distance, 50m or so, welcome everyone to enjoy!
3 Open the simulation file, you can see the direct operation display. The simulation software is used in protues7.5 version.
Platform: |
Size: 214016 |
Author: 无名 |
Hits:
Description: complete wirless design book hope to read
Platform: |
Size: 12906496 |
Author: eng_dina |
Hits:
Description: Tcl script to create dynamic wirless nodes,set initial postion,and set color of node with AODV.
Description:
In this program used to generate the nodes only there is no any other connection between the nodes. After creating the nam file and trace file, we set up topography object. The main thing of the program is how much node you has to give that much node only will create. Otherwise it will cause error. Here nodes have color. Set node_ ($i) [$ns node] is used to create the nodes. Here we set the initial position for the every node by using initial_node_pos. After that $Val (stop) is used to tell to nodes when the simulation ends.-Tcl script to create dynamic wirless nodes,set initial postion,and set color of node with AODV.
Description:
In this program used to generate the nodes only there is no any other connection between the nodes. After creating the nam file and trace file, we set up topography object. The main thing of the program is how much node you has to give that much node only will create. Otherwise it will cause error. Here nodes have color. Set node_ ($i) [$ns node] is used to create the nodes. Here we set the initial position for the every node by using initial_node_pos. After that $Val (stop) is used to tell to nodes when the simulation ends.
Platform: |
Size: 7168 |
Author: Basavaraj |
Hits: