子程序\第十五章  C51单片机软件抗干扰和数字滤波\15.1.1采用指令冗余对程序“跑飞”的软件处理.txt
......\.......................................\15.1.2采用软件陷阱对程序“跑飞”的软件处理实例.txt
......\.......................................\15.1.3软件“看门狗”对程序“跑飞”的处理.txt
......\.......................................\15.1.4通过“复位”使系统恢复正常.txt
......\.......................................\15.2.1汉明码校验.txt
......\.......................................\15.2.2循环冗余校验.txt
......\.......................................\15.3.1程序判断滤波.txt
......\.......................................\15.3.2中值滤波.txt
......\.......................................\15.3.3算术均值滤波.txt
......\.......................................\15.3.4加权平均滤波.txt
......\.......................................\15.3.5滑动平均滤波.txt
......\.......................................\15.3.6防脉冲干扰数字滤波.txt
......\.......................................\15.3.7一阶滞后滤波.txt
......\第十五章  C51单片机软件抗干扰和数字滤波
......\....四章  波形发生与控制实例\14.1.1锯齿波信号发生.txt
......\............................\14.1.2单极性PWM信号发生.txt
......\............................\14.1.3 正弦信号发生.txt
......\............................\14.2.1位置式PID控制.txt
......\............................\14.2.2增量式PID控制.txt
......\第十四章  波形发生与控制实例
......\....三章  单片机数据传输接口\13.1.2数据传输率发生.txt
......\............................\13.1.3单片机RS-485接口.txt
......\............................\13.1.4用外部中断配合查询方式接收串行数据.txt
......\............................\13.1.5 PC机和51单片机的快速串行通信.txt
......\............................\13.1.6单片机多机通信.txt
......\............................\13.2.2通用USB程序模块.txt
......\............................\13.3.1基于I2C的时钟模块X1203.txt
......\............................\13.3.2用两个普通IO模拟I2C总.txt
......\............................\13.4.2 SPI接口LCD显示模块EDM1079.txt
......\............................\13.4.3 SPI接口语音录放模块ISD4104.txt
......\............................\13.4.4 SPI接口时钟日历模块DS1302.txt
......\............................\13.4.5 MICR0WIRE接口E2PR0M存储器NM93Cx6应用.txt
......\............................\13.5.2单总线数字温度传感器.txt
......\............................\13.6.1 CAN接口汇编语言编程.txt
......\............................\13.6.2 CAN接口C语言编程.txt
......\............................\13.7单片机的红外接口.txt
......\第十三章  单片机数据传输接口
......\....二章 51单片机内部资源编程实例\12.1.1 P1口的应用.txt
......\.................................\12.1.2 P0口的扩展使用实例.txt
......\.................................\12.1.3并行IO口编程.txt
......\.................................\12.1.4单片机的FPGA并行配置.txt
......\.................................\12.2.1利用T0、T1作为外部中断源.txt
......\.................................\12.2.2 INT0中断.txt
......\.................................\12.3.1定时器计数器0工作在模式0方式.txt
......\.................................\12.3.2定时器计数器0工作在模式1方式.txt
......\.................................\12.3.3定时器计数器0工作在模式2方式.txt
......\.................................\12.3.4定时器计数器0工作在模式3方式.txt
......\.................................\12.4.2扩展EPROM的.txt
......\.................................\12.4.4扩展EEPROM的.txt
......\.................................\12.5.2扩展RAM到扩展RAM的数据复制.txt
......\.................................\12.5.3扩展RAM到片内RAM数据复制.txt
......\第十二章 51单片机内部资源编程实例
......\....一章  单片机测控接口\11.1 8位AD转换器ADC0809接口.txt
......\........................\11.2 12位AD转换器AD578AD678AD1678接口.txt
......\........................\11.3 12位串行AD转换器接口.txt
......\........................\11.4串行AD转换器MAX187接口.txt
......\........................\11.5 16位AD转换器ADC1143接口.txt
......\........................\11.6单路8位DA转换器DAC0832接口.txt
......\........................\11.7单路10位DA转换器AD7520接口.txt
......\........................\11.8 12位串行DA转换器7543接