Filename
Size
Date
dsPPIC源码\DAC程序\ZZ07_DAC.c
..........\.......\ZZ07_DAC.mcp
..........\p30f6014.gld
..........\p30f6014.h
..........\程序调试说明.doc
..........\第12章 12.6节 EEPROM编程\ProgramEEData.c
..........\........................\ProgramEEData.mcp
..........\...3章 例13-1——TMR1定时器计时的秒表显示\SimpleStopwatch.c
..........\.........................................\SimpleStopwatch.h
..........\.........................................\SimpleStopwatch.mcp
..........\......例13-2—— TMR1定时器控制6个贴片发光二极管的循环亮点\Flicker.c
..........\..........................................................\Flicker.mcp
..........\...4章 例14-1——Timer3定时器比较结束启动AD转换例程\DigitalVoltmeter.c
..........\...................................................\DigitalVoltmeter.h
..........\...................................................\DigitalVoltmeter.mcp
..........\...5章 例15-1——分析输入捕获端口端口信号频率\PulsePeriodMeasure.c
..........\.............................................\PulsePeriodMeasure.h
..........\.............................................\PulsePeriodMeasure.mcp
..........\...6章  例16-1——单比较匹配模式，电平交替翻转输出\OCMPrj1.C
..........\..................................................\OCMPrj1.mcp
..........\.......例16-2——双比较匹配模式，连续的单脉冲输出，占空比34％\OCMPrj2.c
..........\.............................................................\OCMPrj2.mcp
..........\............3——双比较匹配模式，连续脉冲输出，正占空比47％\OCMPrj3.c
..........\...........................................................\OCMPrj3.mcp
..........\............4——不带故障保护输入引脚的PWM
占空比84.04％，选择输出比较OC8\SimplePWMNP.c
..........\.........................................................................\SimplePWMNP.mcp
..........\............5——带故障保护输入引脚的PWM
空比49.27％，选择输出比较OC8\SimplePWMP.c
..........\.....................................................................\SimplePWMP.mcp
..........\...7章 SPI程序
在8个LED数码管上显示数值\ZZ03_8LEDPY.c
..........\.......................................\ZZ03_8LEDPY.mcp
..........\.......例17-2——SPI输出数码管显示程序，用数码管显示按键的击键次数\KeysCounter.c
..........\..................................................................\KeysCounter.mcp
..........\......例 17-1——SPI输出数码显示程序\SimpleSPIOut.c
..........\....................................\SimpleSPIOut.mcp
..........\...8章 I2C应用\ZZ05_I2CEEPROM.c
..........\..............\ZZ05_I2CEEPROM.mcp
..........\..............，PCF8583读写程序\ZZ11_I2Ctime.c
..........\...............................\ZZ11_I2Ctime.mcp
..........\......例18-1——串行EEPROM 24LC256的读写\I2CEEPROM.C
..........\........................................\I2CEEPROM.mcp
..........\...........2——与日历时钟芯片PCF8583通信\I2CTIME.c
..........\.........................................\I2CTIME.h
..........\.........................................\I2CTime.mcp
..........\...9章rs232测试程序\bookRS232.c
..........\...................\bookRS232.mcp
..........\...................\rs232_2.c
..........\...................\rs232_2.mcp
..........\...................\rs232_interupt.c
..........\...................\rs232_interupt.mcp
..........\..20章 例20-1——测试CAN口时，采用了11位标准标识符\ZZ08_CAN.c
..........\..................................................\ZZ08_CAN.mcp
..........\......例 20-2——从一个CAN接口发送到另一个CAN接口\ZZ09_CANtoCAN.c
..........\.................................................\ZZ09_CANtoCAN.mcp
..........\...1章 ADC测试\ZZ06_ADC.c
..........\..............\ZZ06_ADC.mcp
..........\..9章 例9-1——循环点亮6个贴片发光二极管\ZZ01_MiniTEST.c
..........\........................................\ZZ01_MiniTEST.mcp
..........\..........2——利用发光二极管显示按键的击键次数\ZZ02_KeyCounter.c
..........\...............................................\ZZ02_KeyCounter.mcp
..........\.....例 9-3——在液晶显示器上显示信息\ZZ10_LCD1.c
..........\.....................................\ZZ10_LCD1.mcp
..........\DAC程序
..........\第12章 12.6节 EEPROM编程
..........\第13章 例13-1——T