Welcome![Sign In][Sign Up]
Location:
Search - LIGHT-TO-DIGITAL

Search list

[SCMCROSS

Description: 自动交通管理系统 用红、绿、黄三支共两组发光二极管表示交通信号灯,利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下: 1)放行线:绿灯亮放行25秒,黄灯亮警告5秒,然后红灯亮禁止。 2)禁止线:红灯亮禁止30秒,然后绿灯亮放行。 3)当某一方向的红灯亮时,若该方向有车通过,则用扬声器声报警。(撞红灯信号可用3-5V模拟量表示) 同时用2位数码管进行30秒钟递减时间显示。-automatic traffic management system using red, green, yellow a total of three light-emitting diodes, said two traffic lights, using SCM time simulation shows the regular traffic signal control. Signal changes in the law to be as follows : 1) Release Line : green clearance 25 seconds, bright yellow warning five seconds, and then the red-ban. 2) prohibit the lines : red-Ban 30 seconds, then green clearance. 3) When the red light in one direction- that if the direction of a car passed, the use of loudspeakers sound alarm. (Red light signals can hit 3- 5V analog said), while using two digital tube for 30 seconds decreasing time displayed.
Platform: | Size: 2048 | Author: gjb | Hits:

[Othertraficlight

Description: 这是EWB做的关于数字逻辑的课程设计 其中红灯的时间可以自行修改 还设了人行道的红绿灯-This is done on digital logic design courses which time the red light can also set up their own amendments to the People's Bank Road traffic lights
Platform: | Size: 177152 | Author: 胡海洪 | Hits:

[assembly languagejiaotongdeng

Description: 一.设计要求 1.道路有A.B两路,一般情况A.B均有车时,两路各放行10S. 2.红绿灯转换必须经过4秒黄灯闪烁. 3.若两路均无车则保持原状. 4.若一路通行无阻10秒后,另一路无车,则继续放行此路,直到另一路有车. 5.若有紧急车辆通过两路均无红灯4秒,阻止一般车辆通过,让紧急车辆通过6.在数码管显示各路通行的标志和剩余时间. -1. Design requirements 1. Road has two-way AB, AB generally have cars, two of the released 10S. 2. Traffic light conversion must be 4 seconds blinking yellow light. 3. If the two had no car to maintain the status quo. 4. if unimpeded access all the way 10 seconds later, another car-free road, then continue to release this road until the road has another car. 5. if emergency vehicles through two red lights were not four seconds to stop the vehicles passed, so that emergency vehicles through 6. in the digital display various signs and the remainder of the passage of time.
Platform: | Size: 6144 | Author: 刘智峰 | Hits:

[assembly languagemyjiaotongdeng

Description: 本例实现交通灯的控制,用LED显示灯表示交通状态,并以7段数码管显示当前状态剩余秒数。 主干道绿灯亮时,支干道红灯亮,反之依然,二者交替允许通行,主干道每次放行35秒,支干道每次放行25秒。每次由绿灯变为红灯的过程当中,亮光的黄灯作为过度,黄灯时间为5秒。-Example realize the control of traffic lights with LED lights that show the traffic status, and paragraph 7 of the current state of digital tube display the number of seconds remaining. Trunk road when the green light, red light sticks roads, on the contrary still, the two alternating current permit, trunk release per 35 seconds, each route clearance teams and 25 seconds. Every time the green light to red light by the process, the yellow light as the excessive yellow light time was 5 seconds.
Platform: | Size: 465920 | Author: 李东 | Hits:

[Booksaudiowatermark

Description: This discussion will attempt to outline some truths and common misconceptions about digital audio watermarking. It will survey the intrinsic obstacles that such technology is required to overcome, shedding light on its performance criteria, compromises and limitations. While doing so, it will also survey a few common types of applications, hopefully leading to a clear understanding as to the appropriateness of such technology and its expertise within multimedia content protection.
Platform: | Size: 150528 | Author: comein | Hits:

[SCMjiaotongdeng

Description: 本系统采用MSC-51系列单片机ATSC51和可编程并行I/O接口芯片8255A为中心器件来设计交通灯控制器,实现了能根据实际车流量通过8051芯片的P1口设置红、绿灯燃亮时间的功能;红绿灯循环点亮,倒计时剩5秒时黄灯闪烁警示(交通灯信号通过PA口输出,显示时间直接通过8255的PC口输出至双位数码管);车辆闯红灯报警;绿灯时间可检测车流量并可通过双位数码管显示。-The system uses the MSC-51 Series MCU ATSC51 and programmable parallel I/O interface chip 8255A-centric devices to design the traffic light controller, which can realize the basis of actual traffic flow through the P1 port 8051 chip set red, green fuel Liang time function traffic lights lit cycle, the countdown five seconds left when the yellow light flashing warning (traffic lights signal through the PA output, indicating the time directly through the PC port output 8255 to double-digit digital tube) vehicles闯红灯alarm green time can detect the flow through a double-digital tube display.
Platform: | Size: 131072 | Author: eee | Hits:

[VHDL-FPGA-VerilogDesign_of_Traffic_Light_Control_System_Base_on_FPG

Description: 用VHDL 语言设计交通灯控制系统, 并在MAX+PLUS II 系统对FPGA/ CPLD 芯片进行下载, 由于生成的是集成化的数字电 路, 没有传统设计中的接线问题, 所以故障率低、可靠性高, 而且体积小。体现了EDA 技术在数字电路设计中的优越性。-The design method of traffic light control system by using Very- High- Speed Integrated Circuit Hardware Description Language (VHDL) is introduced, and the downloading of the controller design to the FPGA/ CPLD chip in MAX+PLUS II is fulfilled. As FPGA/ CPLD chips are based on large scale IC and there are no connection problems in the presented circuit, so the chips are re1iable and faults are less prone to happen, which shows the advantages of the EDA technology in digital circuits design.
Platform: | Size: 72704 | Author: li | Hits:

[Software Engineeringjiaotongdeng

Description: 本系统采用MSC-51系列单片机ATSC51和可编程并行I/O接口芯片8255A为中心器件来设计交通灯控制器,实现了能根据实际车流量通过8051芯片的P1口设置红、绿灯燃亮时间的功能;红绿灯循环点亮,倒计时剩5秒时黄灯闪烁警示(交通灯信号通过PA口输出,显示时间直接通过8255的PC口输出至双位数码管);车辆闯红灯报警;绿灯时间可检测车流量并可通过双位数码管显示。本系统实用性强、操作简单、扩展功能强。 -The system uses the MSC-51 Series MCU ATSC51 and programmable parallel I/O interface chip 8255A-centric devices to design the traffic light controller, which can realize the basis of actual traffic flow through the P1 port 8051 chip set red, green fuel Liang time function traffic lights lit cycle, the countdown five seconds left when the yellow light flashing warning (traffic lights signal through the PA output, indicating the time directly through the PC port output 8255 to double-digit digital tube) vehicles闯红灯alarm green time can detect the flow through a double-digital tube display. The system practical, simple operation, the expansion of strong functions.
Platform: | Size: 131072 | Author: ljj | Hits:

[VHDL-FPGA-Verilogfpga_led

Description: 这个源代码是由专业人士编的,其作用是点亮数码管,检验开发板的好坏!-This source code is made by professionals, and its role is to light up digital tube, test development board is good or bad!
Platform: | Size: 29696 | Author: 祝宁 | Hits:

[SCMxinlv

Description: 用数码管显示测得的心率值。并控制发光二极管的亮灭。-Digital display of heart rate measured value. And control of light to eliminate light-emitting diodes.
Platform: | Size: 1024 | Author: 徐伟业 | Hits:

[Otherjiaotongdengkongzhi

Description: 东西和南北方向各有一组红、黄、绿灯用于指挥交通,红、黄、绿的持续时间分别为25s,5s,20s。 当有紧急情况(如消防车)时,两个方向均为红灯亮,计时停止,当特殊情况结束后,控制器恢复原来状态,正常工作。 一组数码管,以倒计时方式显示两个方向允许通行或禁止通行的时间。-East-West and North-South direction of a different set of red, yellow and green light for directing traffic, red, yellow and green are the duration of 25s, 5s, 20s. When there are emergency situations (such as fire engines), the two directions are the red light, stop time, when the special circumstances of the end of the controller to restore the original state, the normal work. A group of digital controls to display the countdown in two directions to allow access or prohibit the passage of time.
Platform: | Size: 547840 | Author: 黄巍 | Hits:

[VHDL-FPGA-VerilogDigitalclocksignal

Description: 数字时钟信号用vhdl语言描述的源代码他光放利用到各个电路中-Vhdl digital clock signal with the source code language to describe his use of light to release all circuits
Platform: | Size: 5120 | Author: qing | Hits:

[SCMtraficlight

Description: 东西南北四个方向各有一组红绿黄指示灯和两个数码管,东西方向和南北方向交替允许通道,当西南方向允许通行亮绿灯时,南北方向亮红灯,当南北方向允许通行亮绿灯时,东西方向亮红灯,放行时间都是40秒,在每次由绿灯变为红灯时,要闪烁5秒钟黄灯作为过渡,在设置一按钮按下改按钮后,东西南北四个方向均亮红灯,数码管显示0,再按一次该按钮交通灯正常工作。-Each of the four north-south direction of things a group of yellow red and green LED indicator light and two east-west direction and north-south direction of the turn to allow access, when the south-west passage to allow a green light, the north-south direction of red, when the prevailing north-south direction to allow a green light when the red east-west direction, release time is 40 seconds, each time from when the red light into green light to yellow light flashes 5 seconds as a transitional, in the settings by pressing a button to button, the four north-south east-west the direction of both the red, digital display 0, and then once the button traffic lights work properly.
Platform: | Size: 58368 | Author: 周晨 | Hits:

[Other73462676Light

Description: VC6.0在OPENGL中的运用,用于实现光照效果的一个简单程序-VC6.0 in OPENGL in the use of lighting effects used to implement a simple program
Platform: | Size: 251904 | Author: zz | Hits:

[ELanguagelight-dependent-resistorat89s52

Description: Description: The ability to convert analog signals to digital and vice-versa is very important in signal processing. The objective of an A/D converter is to determine the output digital word corresponding to an analog input signal.
Platform: | Size: 15360 | Author: hirmon | Hits:

[Software EngineeringTraffic-light-controller

Description: 交通灯控制器在A、B方向各有红、黄、绿三盏灯,其控制顺序按表的设计进行循环,表中1表示灯亮、0表示灯灭。交通灯控制器按照主干道数码管显示50S,支干道数码管显示30S, 主干道变为红灯,支干道变为绿灯,继续进行倒计时;支干道倒计时结束后再经行5秒倒计时,交通灯变为黄灯;支干道倒计时结束后再回到初始状态。-Traffic light controller in A, B direction of each red, yellow, and green light, the control sequence of the design cycle according to the table, the table 1 that light, 0 is lights out. Main road traffic light controller in accordance with digital display 50S, branch roads digital display 30S, the main road into the red, branch roads into the green light to continue the countdown branch roads countdown after the end of the line five seconds after the countdown, traffic lights becomes yellow branch roads after the end of the countdown to the initial state.
Platform: | Size: 9216 | Author: zhangcand | Hits:

[CSharplight

Description: ARM-M0-LPC1114 ISL29003光照度芯片 光照度程序-Driver for the ISL29003 Light-to-Digital Output Sensor
Platform: | Size: 2048 | Author: jory | Hits:

[SCMlight

Description: 将光敏电阻采集到的电压信号经MSP430中ADC12转换为数字信号-ADC12 in MSP430 convert the anolog voltage collected by photoresistance to digital value
Platform: | Size: 20480 | Author: 张丽 | Hits:

[Linux-Unixtcs3472

Description: tcs3472.c - Support for TAOS TCS3472 color light-to-digital converter.
Platform: | Size: 3072 | Author: jqdanbg | Hits:

[Embeded-SCM DevelopSound-and-light---temperature-alarm

Description: 1、温度显示 声光型数字温度报警器是基于单片机控制的数字化功能平台。以单片机为核心控制的电路,结合数码管及其它元器件的使用,温度传感器接收温度,通过电路,使它能在数码管上显示。 2、温度报警 通过C语言编写的程序来控制单片机的运行,设置上限温度,当温度达到所设定的温度时,蜂鸣器就接通,发出声音,提示温度超过所设定。 3.报警解除 当实际温度超过所设定的温度时,蜂鸣器报警,如果要切断报警,可以做出终止报警,但是温度还在数码管上显示。 -1, temperature display The sound and light type digital temperature alarm is a digital function platform based on single chip microcomputer control. With single chip microcomputer as the core control circuit, combined with the use of digital control and other components, temperature sensor to receive temperature, through the circuit, so that it can display on the digital tube. 2, temperature alarm Through the C language program to control the operation of the microcontroller, set the upper limit temperature, when the temperature reaches the set temperature, the buzzer will switch on, sound, prompt temperature exceeds the set. 3 alarm release When the actual temperature exceeds the set temperature, the buzzer alarm, if you want to cut off the alarm, you can make the termination of the alarm, but the temperature is still displayed on the digital tube.
Platform: | Size: 97280 | Author: | Hits:
« 12 3 4 5 6 7 8 9 10 ... 26 »

CodeBus www.codebus.net