Description: 在PIC16F877上驱动OCM2×8C液晶模块LCM，LCD的驱动程序。在LCD.c文件头部给出了硬件连接方法，在OCM2×8Creadme.doc中还给出了详细介绍并附有C51的汇编代码。-PIC16F877 on the drive in OCM2 × 8C LCD module LCM, LCD drivers. LCD.c document in the head gives the hardware connection methods OCM2 × 8Creadme.doc also gives a detailed introduction with C51 assembly code. Platform: |
Size: 66560 |
Author:王萧风 |
Hits:
Description: 这是一个4*4键盘控制液晶显示器的汇编语言程序。是用MICROCHIP的MPLAB IDE编写的。附有硬件连接方式。-this is a 4* 4 keyboard control LCD assembly language. Is going before the MPLAB IDE prepared. With hardware connectivity options. Platform: |
Size: 16384 |
Author:陈燕 |
Hits:
Description: SSD1815 controller BO9864A graphic LCD Test driver using assembly language.
It is good example driver source code for other graphic LCD using SSD1815 controller-SSD1815 controller BO9864A graphic LCD Test driver using assembly language.It is good example driver source code for other graphic LCD using SSD1815 controller Platform: |
Size: 7168 |
Author:David |
Hits:
Description: s3c44b0 的开发板测试的所有源代码及程序！！！汇编代码主要完成系统初始化，包括：
禁止看门狗；
禁止所有中断；
初始化存储器（包括SDRAM）；
设定锁相环倍频；
使能所有单元模块时钟；
初始化堆栈；
设置中断等等
C语言代码主要是应用代码，包括：
设置使用指令缓存；
修改系统主时钟为32MHz；
IO端口功能、方向设定；
初始化中断；
初始化DMF50081液晶模块；
蜂鸣器测试；
液晶显示测试；
LED输出测试；
定时器、PWM测试等；-S3C44B0 development board to test all source code and procedures! ! ! Assembly code to initialize the main complete system, including: the prohibition of watchdog ban all interrupted initialize memory (including SDRAM) set PLL multiplier so that all clock modules initialize stack settings interruption, etc. C language code is application code, including: the use of instruction cache settings modify the system master clock is 32MHz IO port functions, the direction of settings initialization interrupt DMF50081 LCD module initialization buzzer test LCD test LED output test timer, PWM testing Platform: |
Size: 4096 |
Author:叶凌 |
Hits:
Description: 这是利用汇编语言编写的液晶显示屏的程序代码，简短而又易懂，可供参考-This is prepared by the use of assembly language code of the LCD screen, the short and easy to understand, for reference Platform: |
Size: 3072 |
Author:王盗大 |
Hits:
Description: 8051 Assembly code to control the character based LCD display.
Different display was supported. Platform: |
Size: 6144 |
Author:lzm |
Hits:
Description: Digital clock for 8051 or 8052 micro-controller.This clock used the 16 x 2 LCD to display the time. Interrupt 0 and 1 used to adjust the minutes and hour.-This is simple assembly code to program the digital clock.Very easy to understand. Platform: |
Size: 1024 |
Author:anthonykang |
Hits:
Description: 基于博创实验箱UP-CUP-FPGA2C35-Ⅱ和Verilog HDL硬件描述语言，分为按键输入模块、LED指示灯模块及LCD显示模块，采用按键BTN1、BTN2作为输入端输入四位密码与事先设定的密码进行匹配，由D1、D2、D3、D4四盏LED灯来指示输入密码的位数。开机时，LCD显示“HELLO! WELCOME!Enter the code:当”，密码输入正确时，LED灯D7亮，同时在实验箱LCD显示屏上显示字符串“Good! Well done!you are right!!!”，当密码输入错误时，LED灯D8亮，并在LCD显示屏上显示字符串“NO!!You stupid!!you are worry!!!”其中，LCD显示作为本次设计的核心内容，字符型LCD通常有14条引脚线或16条引脚线的LCD，多出来的2条线是背光电源线VCC(15脚)和地线GND(16脚)，其控制原理与14脚的LCD完全一样-Base YuBo gen experiment box UP- FPGA2C35- Ⅱ and director- Verilog HDL hardware description language, divided into key input module, the LED indicator light module and LCD display module, the BTN1, BTN2 buttons as input the input password and set in four matches, the password by D1, D2 and D3, D4 four lamp that LED lamp to indicate input password of digits. Boot, LCD display "HELLO!!!!!!!!!! The code: backgound Enter when", a password when right, LED lamp, while D7 light displayed on the LCD screen experiment box string "Good!! Well done! You right!!!" hero When a password mistake, LED lamp light, and in D8 displayed on the LCD screen "NO!! You string can be hindered stupid!!!!!!!!!!!!!!!!!" hero Among them, LCD display as the core content of the design, character type LCD usually has 14 pin line or 16 pins line of LCD, extra 2 line is backlit cord VCC (15 feet) and landlines GND (16 feet), the control principle and 14 feet LCD exactly the same
Platform: |
Size: 3072 |
Author:吴寿武 |
Hits:
Search - lcd assembly code