Search - lift controller

[SCM] DTXT

Description: 用单片机实现电梯控制系统电梯控制系统的工作原理是：当某层有要梯信号输入时，呼梯信号锁存系统将要梯信号锁存，待单片机查询到要梯信号后，根据要梯信号的位置(即楼层数)和电梯所处的位置，决定电梯运行方向，并启动电梯到要梯层停梯、开门，待乘客进入电梯关门后，再根据乘客要求把乘客送到目的层。-with MCU elevator control system of the elevator control system working principle is : When a staircase layer to the input signal, calling signal latch system will be staircase signal latches, SCM pending inquiries to the staircase to signal, according to the location staircase signal (that is, number of floors) and the locations of elevators, decide the direction of the lift operation, and start to the elevator to stop staircase layer Ossetia, opened the door, the passengers entered the elevator closed, According passengers require passengers to the target zone.
Platform: | Size: 111616 | Author: 方凯旋 | Hits:

[Other systems] elevator

Description: 电梯控制器可实现电梯上下响应任务，到站提示音，无任务停在基站-Elevator controller can realize the lift up and down in response to mission departure and arrival tone, non-mission stopped at the base station
Platform: | Size: 1024 | Author: hilly | Hits:

[VHDL-FPGA-Verilog] lift

Description: 采用vhdl语言的电梯控制器源代码，能够实现报警，等待，并采用了标准的最优电梯运动路线。-Using VHDL language elevator controller source code, to realize the police, waiting, and the optimal use of the standard line of lift movement.
Platform: | Size: 2048 | Author: wriuwru | Hits:

[Delphi VCL] e-controller

Description: 模拟电梯调度程序，有详细操作界面，全真模拟电梯运行状况-Simulated elevator scheduling procedures, a detailed user interface, full simulation of the lift operation
Platform: | Size: 295936 | Author: ones | Hits:

[VHDL-FPGA-Verilog] Lift

Description: VHDL编写的6层电梯控制器，可在Altera的CPLD系统运行实验，内附实验报告-VHDL prepared 6-storey elevator controller in Altera s CPLD system experiment, experimental report containing
Platform: | Size: 770048 | Author: 许昕 | Hits:

[VHDL-FPGA-Verilog] lift

Description: （1）用VHDL实现四层电梯运行控制器。（2）电梯运行锁用一按钮代替（开锁上电），低电平可以运行，高电平不能运行。（3）每层电梯入口处设有上行、下行请求按钮，电梯内设有乘客到达层次的停站要求开关，高电平有效。（4）有电梯所处楼层指示灯和电梯上行、下行状态指示灯。（5）电梯到达某一层时，该层指示灯亮，并一直保持到电梯到达另一层为止。电梯上行或下行时，相应状态指示灯亮。（6）电梯接收到停站请求后，每层运行2秒，到达停站层，停留2秒后门自动打开，开门指示灯亮，开门6秒后电梯自动关门。（7）能记忆电梯内、外的请求信号，并按照电梯的运行规则依次响应，请求信号保留至响应后撤除。（8）人数超载或超重用一按钮代替，高电平有效，超载时电梯不能运行，并有相应指示。（9）事故报警按钮高电平有效，事故报警不能运行，并有指示灯，信号保留至事故消除 -(1) the realization of four-storey elevator with VHDL controller operation. (2) elevator button with a lock to run in place of (unlock power), low run, can not run high. (3) on each floor with elevator at the entrance to the uplink, downlink request button, which are equipped with passenger elevators to reach the level of the requirements of stoppings switch, high effective. (4) elevators and escalators which lights up the floor, down the state indicator. (5) elevator to reach a certain level, the level indicator light, and has remained until the elevator arrived at another level. Elevator uplink or downlink, the corresponding status indicator light. (6) Elevator stops receiving a request, each running two seconds to reach the stops layer, two seconds back door stay open automatically, open the door indicator light, 6 seconds after the elevator door closed automatically. (7) to memory elevator inside and outside the request signal, and in accordance with the rules followed
Platform: | Size: 289792 | Author: 管皮皮 | Hits:

[VHDL-FPGA-Verilog] dianti.vhd

Description: 电梯控制器的VHDL源程序很有代表性经简单修改后可用于n层控制 -Lift Controller
Platform: | Size: 5120 | Author: jimmy | Hits:

[Software Engineering] lift

Description: 基于FPGA的自动升降电梯控制器设计 PDF文档详细的开发思路-FPGA-based controller design for automatic elevators PDF documents in detail the development of ideas
Platform: | Size: 289792 | Author: Hugh | Hits:

[VHDL-FPGA-Verilog] lift

Description: 设计一个八层楼房自动电梯控制器，用八个 LED显示电梯行进过程，并有数码管显示电梯当前所在楼层位置，在每层电梯入口处设有请求按钮开关，请求按钮按下则相应楼层的LED 亮。 -Design a controller, eight-story buildings, escalators, moving elevator with eight LED display process, and a digital display where the floor lift the current location of the entrance at each elevator button switch with a request, the request button is pressed the corresponding floor LED light.
Platform: | Size: 76800 | Author: zhaorongjian | Hits:

[VHDL-FPGA-Verilog] three-lift

Description: 三层电梯控制器上下楼请求信号优先级控制-Three elevator controller down request signal priority control
Platform: | Size: 387072 | Author: woyaochilizhi | Hits:

[VHDL-FPGA-Verilog] VHDL-dianti

Description: 高楼电梯自动控制系统(Windows平台上运行的ispLEVER编程软件。 ): 1统控制的电梯往返于1-9层楼。 2客要去的楼层数可手动输入并显示（设为A数）。 3梯运行的楼层数可自动显示（设为B数）。 4A>B时，系统能输出使三相电机正转的时序信号，使电梯上升；当A<B时，系统能输出使三相电机反转的时序信号，使电梯下降；当A=B时，系统能输出使三相电机停机的信号，使电梯停止运行并开门； 5是上升还是下降各层电梯门外应有指示，各层电梯门外应有使电梯上升或下降到乘客所在楼层的控制开关。注：此为word文档，但里面有源代码。-High-rise elevator control system (Windows platform programming software running on the ispLEVER. ): An elevator control system and from 1-9 floors. 2, the number of passengers going to the floor can manually enter and display (Make A number). 3 ladder run automatically display the number of floors (Set B number). 4A> B, the system can output three-phase motor is transferred to the timing signal to lift up When A <B, the system can output three-phase motor to reverse the timing signal to the lift down When A = B, the system can output a signal to shut down three-phase motor, so that the lift stops and open the door 5 is increasing or decreasing the lift on each floor outside the door should be directed, due to lift on each floor outside the elevator up or down to the floor where the passenger control switch. Note: This is a word document, but inside the source code.
Platform: | Size: 34816 | Author: | Hits:

[Windows Develop] 1~9dianti

Description: 1 三层电梯控制器将实现的功能 (1)每层电梯入口处设有上下请求开关，电梯内设有顾客到达层次的停站请求开关。 (2)设有电梯入口处位置指示装置及电梯运行模式(上升或下降)指示装置。 (3)电梯每秒升(降)一层楼。 (4)电梯到达有停站请求的楼层，经过1秒电梯门打开，开门指示灯亮，开门4秒后，电梯门关闭(开门指示灯灭)，电梯继续进行，直至执行完最后一个请求信号后停留在当前层。 (5)能记忆电梯内外所有请求，并按照电梯运行规则按顺序响应，每个请求信号保留至执行后消除。 (6)电梯运行规则一当电梯处于上升模式时，只响应比电梯所在位置高的上楼请求信号，由下而上逐个执行，直到最后一个上楼请求执行完毕；如果高层有下楼请求，则直接升到由下楼请求的最高层，然后进入下降模式。当电梯处于下降模式时则与上升模式相反。 (7)电梯初始状态为一层开门状态。 -A three-lift controller functions to be achieved (1) the entrance of each floor with elevator up and down the request switch, the elevator is equipped with customer requests to reach levels stop switch. (2) with elevator entrance and elevator position indicator device operation mode (up or down) installation instructions. (3) elevators per liter (lower) floor. (4) The elevator reaches a floor request stops after 1 second elevator door open, open indicator light, open 4 seconds, the elevator doors closed (Open LED OFF), the lift continued until the implementation of the complete signal after the last request to stay in the current layer. (5) can remember all requests inside and outside the elevator and elevator operation in accordance with the rules in order to respond to each request signal to be retained until after the implementation of consumer In addition. (6) the operating rules of an elevator when the elevator is up mode, the only response to the h
Platform: | Size: 3072 | Author: 许敏 | Hits:

[VHDL-FPGA-Verilog] lift

Description: 用VHDL编写的全功能四层电梯控制器-Prepared with a fully functional VHDL four elevator controller. . .
Platform: | Size: 17408 | Author: aiyun | Hits:

[File Format] me-lift-f

Description: MOTOROLA CPU me-lift-f经济型微机电梯控制系统用户手册主控制器采用性能优良稳定的美国MOTOROLA 公司的CPU，系统更可靠。 MOTOROLA 的CPU 在工业控制领域占有重要地位，是世界上嵌入式处理器最大的供货商，广泛应用于工业控制、汽车电子、消费电子的各个领域。 MOTOROLA CPU 内部集成看门狗电路,具有极强的抗干扰性能。采用锁相环技术，能降低 CPU 外部频率，增强干扰能力。-MOTOROLA CPU me-lift-f cheap computer user manual elevator control system with excellent performance and stability with the main controller of the United States MOTOROLA' s CPU, the system more reliable. MOTOROLA' s CPU in the field of industrial control occupies an important position, is the world' s largest supplier of embedded processors are widely used in industrial control, automotive electronics, consumer electronics fields. MOTOROLA CPU watchdog circuit within the integrated, with a strong anti-interference performance. Using PLL technology to reduce the CPU external frequency, and enhance interference.
Platform: | Size: 704512 | Author: 夜路 | Hits:

[SCM] Lift-controller

Description: 这是一款用菲凌8PS56开发的一款升降机控制器，内含功能要求及源码，脚位功能:17.18.1.2脚为控制信号,8.9.10.11,12为输出信号-This is a used Feiling 8PS56 the development of a lift controller, including functional requirements and source code, pin functions: 17.18.1.2 feet for the control signal, the output signal 8.9.10.11,12
Platform: | Size: 86016 | Author: 张朝红 | Hits:

[SCM] lift-controller-89s52

Description: elevator controller fot the trolley
Platform: | Size: 84992 | Author: maheru | Hits:

[Embeded-SCM Develop] PCL-lift-control-system

Description: PLC电梯控制系统：本文介绍了利用可编程控制器编写的一个五层电梯的控制系统，检验电梯PLC控制系统的运行情况。实践证明，PLC可遍程控制器和MCGS组态软件结合有利于PLC控制系统的设计、检测，具有良好的应用价值。-PCL lift control system: The introduction to this text utilizes the control systems of a five- storeyed lift where the programmable controller is written, running situation of the inspection lift PLC control system. Practice has proved PLC can is it favorable to design , measuring , PLC of control system to combine all over between controller and MCGS configuration software Cheng, have good using value .
Platform: | Size: 278528 | Author: liqin | Hits:

Category

Source Code

Web/Internet

Develop Tools

Document

Other

Search in results

OS

Platform

Language

File Type

Search list

[SCM] DTXT

[Other systems] elevator

[VHDL-FPGA-Verilog] lift

[Delphi VCL] e-controller

[VHDL-FPGA-Verilog] Lift

[VHDL-FPGA-Verilog] lift

[VHDL-FPGA-Verilog] dianti.vhd

[Software Engineering] lift

[VHDL-FPGA-Verilog] lift

[VHDL-FPGA-Verilog] three-lift

[VHDL-FPGA-Verilog] VHDL-dianti

[Windows Develop] 1~9dianti

[VHDL-FPGA-Verilog] lift

[File Format] me-lift-f

[SCM] Lift-controller

[SCM] lift-controller-89s52

[Embeded-SCM Develop] PCL-lift-control-system

[VHDL-FPGA-Verilog] vikash_lift---Copy

[VHDL-FPGA-Verilog] assg-9-1-(lift-controller)

[assembly language] lift-code

CodeBus www.codebus.net