Description: It concerns about the MU-MIMO precoding. We compare the BER performance of ZF channel inverse, MMSE channel inverse, MMSE receiver algorithms. Platform: |
Size: 2787 |
Author:peterzhou |
Hits:
Description: This is a code for simulation of BPSK receiver using Direct Sequence Spread Spectrum. The performance is evaluated in presence of AWGN and Rayleigh fading. Platform: |
Size: 2637 |
Author:ruanyap |
Hits:
Description: There are two files in the zip folder. bpsk_spread.m and jakesmodel.m
Steps for simulation:
1] Run jakesmodel.m first
2] Then run bpsk_spread.m .
3] Note that during the first run bpsk_spread.m has no rayleigh fading.This is because the corresponding code has been commented
4] The resulting performance is stored in BER_awgn.
5] Now uncomment the Rayleigh Fading code in bpsk_spread.m file.
6] Same time comment BER_awgn (line 112) and uncomment BER_ray variable.
7] Run the simulation.
To compare the perfromances of the receiver using DSSS plot the BER_awgn and BER_ray
>>semilogy([1:8],BER_awgn(1:8), g* )
hold on
semilogy([1:8],BER_ray(1:8), -.b* )
hold on
grid on
-There are two zip files in the folder. Bpsk_ spread.m and jakesmodel.m Steps for simulatio n : 1] Run jakesmodel.m first 2] Then run bpsk_spre ad.m. 3] Note that during the first run bpsk_spr ead.m has no Rayleigh fading.This is because th e corresponding code has been commented 4] The r esulting performance is stored in BER_awgn. 5] Now uncomment the Rayleigh Fading code in bpsk_ spread.m file. 6] Same time comment BER_awgn (l 112 produced mostly in developed areas) and uncomment BER_ray variable. 7] Run the simulation. To compare the perfromances of the receiver using DSSS plot and the BER_awgn BE R_ray Platform: |
Size: 3072 |
Author:朱振希 |
Hits:
Description: FM 接收机测试方法:
为了接收性能的比较及评价，作为规定测试方法。另外，ＦＭ ＭＰＸ 立体声接收机也适用于此测试方法
-FM receiver testing method : To compare the performance of the receiving and evaluation, as a required test. In addition, the FM stereo receiver MPX also apply to this test method Platform: |
Size: 30720 |
Author:基本原则 |
Hits:
Description: 本程序对rake接收机的仿真程序
在matlab simulink下实现，其信道模型采用802.15.3a信道，信源部分的采用UWB信号，最后通过计算snr与errorbitrate来说明rake接收机性能-this program right rake receiver in the simulation program under Matlab Simulink. its channel model used 802 .15.3 a letter, the source of the signal using UWB, Finally, with errorbitrate snr calculated to illustrate rake receiver performance Platform: |
Size: 24576 |
Author:volvo827 |
Hits:
Description: This code was used for making the practical measurements in section 2.3 of my thesis. This Matlab code allows an OFDM signal to be generated based on an input data file. The data can be random data, a grey scale image, a wave file, or any type of file. The generated OFDM signal is stored as a windows wave file, allowing it to be viewed, listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data. This code was developed for the experiments that I performed in my honours thesis, and thus has not been fully debugged.
This is the original code developed for the thesis and so has several problems with it. The BER performance given by the simulations is infact Symbol Error Rate.
-This code was used for making the practical measurements in section 2.3 of my thesis. This M atlab code allows an OFDM signal to be generated based on an input data file. The data can be rando m data, a gray scale image, a wave file, or any type of file. The OFDM signal is generated stored as a windows wave file, allowing it to be viewed. listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data . This code was developed for the experiments th at I performed in my honors thesis, and thus has not been fully debugged. This is the original code developed for the thesis and so ha 's several problems with it. The BER performance given by the simulations is infact Symbol Error Rate. Platform: |
Size: 161792 |
Author:王文 |
Hits:
Description: AV系统数字调谐PLL频率合成器的单片机控制
文章利用LC7218PLL频率合成器在AV领域的电调谐功能,提出了一个TV/FM/AM全景接收机设计方案,重点设计分析了LC7218与单片机之间的I/O数据结构,显示了它优良的性能。-AV system PLL digital tuning of the single-chip frequency synthesizer to control the use of article LC7218PLL frequency synthesizer in the AV field of electrical tuning function, a TV/FM/AM panoramic receiver design programs that focus on design and analysis of the LC7218 and MCU between the I/O data structure, demonstrated its excellent performance. Platform: |
Size: 96256 |
Author:love2008 |
Hits:
Description: ：首先介绍了DS--UWB系统的的发射与接收模型，然后分析了利用滑动相关法对信道进行估讣，并巾此给出
了不同RAKE接收机RAKE合成权系数选取方案。对接收机采用最大比(MRC)、最小均方误差(MM SE)及带均衡
器的(MRC)合并系数选取的误码性能进行了仿真和对比。结果表明了带均衡器的MRC—RAKE只用较少的分支
就可以达到接收性能明显优于MMSE—RAKE的程度。尤其在信噪比比较大时。这种优势更加明显。-: First of all, the introduction of the DS UWB system model of the launch and reception, and then analyzed using the sliding correlation method for estimation of channel obituary, and towels, this gives the RAKE receiver RAKE synthesis of different weights to select the program. On the receiver using maximal ratio (MRC), minimum mean square error (MM SE) and band equalizer (MRC) combined coefficient selected BER simulation and comparison. The results show that the equalizer with MRC-RAKE only with fewer branches on the receiver performance can be achieved significantly better than MMSE-RAKE level. Particularly in the relatively large signal to noise ratio. This advantage becomes even more evident. Platform: |
Size: 207872 |
Author:季昀 |
Hits:
Description: ：首先介绍了DS--UWB系统的的发射与接收模型，然后分析了利用滑动相关法对信道进行估讣，并巾此给出
了不同RAKE接收机RAKE合成权系数选取方案。对接收机采用最大比(MRC)、最小均方误差(MM SE)及带均衡
器的(MRC)合并系数选取的误码性能进行了仿真和对比。结果表明了带均衡器的MRC—RAKE只用较少的分支
就可以达到接收性能明显优于MMSE—RAKE的程度。尤其在信噪比比较大时。这种优势更加明显。-: First of all, the introduction of the DS UWB system model of the launch and reception, and then analyzed using the sliding correlation method for estimation of channel obituary, and towels, this gives the RAKE receiver RAKE synthesis of different weights to select the program. On the receiver using maximal ratio (MRC), minimum mean square error (MM SE) and band equalizer (MRC) combined coefficient selected BER simulation and comparison. The results show that the equalizer with MRC-RAKE only with fewer branches on the receiver performance can be achieved significantly better than MMSE-RAKE level. Particularly in the relatively large signal to noise ratio. This advantage becomes even more evident. Platform: |
Size: 151552 |
Author:季昀 |
Hits:
Description: ：首先介绍了DS--UWB系统的的发射与接收模型，然后分析了利用滑动相关法对信道进行估讣，并巾此给出
了不同RAKE接收机RAKE合成权系数选取方案。对接收机采用最大比(MRC)、最小均方误差(MM SE)及带均衡
器的(MRC)合并系数选取的误码性能进行了仿真和对比。结果表明了带均衡器的MRC—RAKE只用较少的分支
就可以达到接收性能明显优于MMSE—RAKE的程度。尤其在信噪比比较大时。这种优势更加明显。-: First of all, the introduction of the DS UWB system model of the launch and reception, and then analyzed using the sliding correlation method for estimation of channel obituary, and towels, this gives the RAKE receiver RAKE synthesis of different weights to select the program. On the receiver using maximal ratio (MRC), minimum mean square error (MM SE) and band equalizer (MRC) combined coefficient selected BER simulation and comparison. The results show that the equalizer with MRC-RAKE only with fewer branches on the receiver performance can be achieved significantly better than MMSE-RAKE level. Particularly in the relatively large signal to noise ratio. This advantage becomes even more evident. Platform: |
Size: 44032 |
Author:季昀 |
Hits:
Description: ：首先介绍了DS--UWB系统的的发射与接收模型，然后分析了利用滑动相关法对信道进行估讣，并巾此给出
了不同RAKE接收机RAKE合成权系数选取方案。对接收机采用最大比(MRC)、最小均方误差(MM SE)及带均衡
器的(MRC)合并系数选取的误码性能进行了仿真和对比。结果表明了带均衡器的MRC—RAKE只用较少的分支
就可以达到接收性能明显优于MMSE—RAKE的程度。尤其在信噪比比较大时。这种优势更加明显。-: First of all, the introduction of the DS UWB system model of the launch and reception, and then analyzed using the sliding correlation method for estimation of channel obituary, and towels, this gives the RAKE receiver RAKE synthesis of different weights to select the program. On the receiver using maximal ratio (MRC), minimum mean square error (MM SE) and band equalizer (MRC) combined coefficient selected BER simulation and comparison. The results show that the equalizer with MRC-RAKE only with fewer branches on the receiver performance can be achieved significantly better than MMSE-RAKE level. Particularly in the relatively large signal to noise ratio. This advantage becomes even more evident. Platform: |
Size: 1024 |
Author:季昀 |
Hits:
Description: ：首先介绍了DS--UWB系统的的发射与接收模型，然后分析了利用滑动相关法对信道进行估讣，并巾此给出
了不同RAKE接收机RAKE合成权系数选取方案。对接收机采用最大比(MRC)、最小均方误差(MM SE)及带均衡
器的(MRC)合并系数选取的误码性能进行了仿真和对比。结果表明了带均衡器的MRC—RAKE只用较少的分支
就可以达到接收性能明显优于MMSE—RAKE的程度。尤其在信噪比比较大时。这种优势更加明显。-: First of all, the introduction of the DS UWB system model of the launch and reception, and then analyzed using the sliding correlation method for estimation of channel obituary, and towels, this gives the RAKE receiver RAKE synthesis of different weights to select the program. On the receiver using maximal ratio (MRC), minimum mean square error (MM SE) and band equalizer (MRC) combined coefficient selected BER simulation and comparison. The results show that the equalizer with MRC-RAKE only with fewer branches on the receiver performance can be achieved significantly better than MMSE-RAKE level. Particularly in the relatively large signal to noise ratio. This advantage becomes even more evident. Platform: |
Size: 1024 |
Author:季昀 |
Hits:
Description: 设计实现了DSSS通信中RAKE接收的功能，包括m序列生成的m文件和一个数据源扩展程序，可以仿真RAKE接收的误码率，便于分析性能！-Design and Implementation of a DSSS communication RAKE receiver functions, including the m sequence generated m file and a data source extension, you can simulation RAKE receiver BER to facilitate analysis of the performance! Platform: |
Size: 1024 |
Author:ninghongyu |
Hits:
Description: There are two files in the zip folder. bpsk_spread.m and jakesmodel.m
Steps for simulation:
1] Run jakesmodel.m first
2] Then run bpsk_spread.m .
3] Note that during the first run bpsk_spread.m has no rayleigh fading.This is because the corresponding code has been commented
4] The resulting performance is stored in BER_awgn.
5] Now uncomment the Rayleigh Fading code in bpsk_spread.m file.
6] Same time comment BER_awgn (line 112) and uncomment BER_ray variable.
7] Run the simulation.
To compare the perfromances of the receiver using DSSS plot the BER_awgn and BER_ray
Platform: |
Size: 5120 |
Author:xionghailiang |
Hits:
Description: Matlab is an ideal tool for simulating digital communications systems, thanks to
its easy scripting language and excellent data visualization capabilities. One of the
most frequent simulation tasks in the field of digital communications is bit-error-
rate testing of modems. The bit-error-rate performance of a receiver is a figure of
merit that allows different designs to be compared in a fair manner. Performing
bit-error-rate testing withMatlab is very simple, but does require some prerequisite
knowledge Platform: |
Size: 63488 |
Author:宋 |
Hits:
Description: 在单一天线接收和发送的UWB中Rake接收机BER的性能的仿真-In a single antenna to receive and send the UWB in the BER performance of Rake Receiver Simulation Platform: |
Size: 8192 |
Author:蔺佳庆 |
Hits:
Description: In this project we analyze and design the minimum mean-square error (MMSE) multiuser receiver for uniformly quantized synchronous code division multiple access (CDMA) signals in additive white Gaussian noise (AWGN) channels.This project is mainly based on the representation of uniform quantizer by gain plus additive noise model. Based on this model, we derive the weight vector and the output signal-to-interference ratio (SIR) of the MMSE receiver. The effects of quantization on the MMSE receiver performance is characterized in a single parameter named 鈥漞quivalent noise variance鈥? The optimal quantizer stepsize which maximizes the MMSE receiver output SNR is also determined.-In this project we analyze and design the minimum mean-square error (MMSE) multiuser receiver for uniformly quantized synchronous code division multiple access (CDMA) signals in additive white Gaussian noise (AWGN) channels.This project is mainly based on the representation of uniform quantizer by gain plus additive noise model. Based on this model, we derive the weight vector and the output signal-to-interference ratio (SIR) of the MMSE receiver. The effects of quantization on the MMSE receiver performance is characterized in a single parameter named 鈥漞quivalent noise variance鈥? The optimal quantizer stepsize which maximizes the MMSE receiver output SNR is also determined. Platform: |
Size: 147456 |
Author:prasad |
Hits:
Description: 分析了LTE系统频率偏移，定时误差，信道估计问题等，并对广义Rake接收机和CPEDS接收机的性能做了比较。-Analysis of the LTE system frequency offset, timing error, channel estimation problems, and generalized Rake receiver performance receiver and CPEDS were compared. Platform: |
Size: 4240384 |
Author:penglu |
Hits:
Search - performance receiver